Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2133211members
1463909discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

HWIC-16A Configuration - Hardware fault?

I'm trying to configure a HWIC-16A as a terminal server without success. I can get a telnet session to connect, but I simply get a blank screen, no data appears to be sent or received over the serial line.The only similar post I could find was https:...

Cisco Catalyst 9115ax slow wifi

I'm looking for some help to pint me in the right direction.I have a Cisco Catalyst 9115e AX wireless access point running the embedded wireless LAN controller in my home lab.I have a SSID configured using WPA2/3 and dropping me into the correct VLAN...

by • Not applicable
  • 6 Views
  • 0 replies
  • 0 Helpful votes

VTP issue

Hi All, i have an vtp server switch i want that my client switch get an vlan from server switch..but client switch unable to get an vlans from server...please find server switch trunk config:description "3850_Switch_VTP"switchport trunk encapsulation...

hamza-ali by • Spotlight
  • 7 Views
  • 0 replies
  • 0 Helpful votes

VXLAN BGP EVPN Default Route

Hello all,  On Border Edges(DC01-BE001-6/7) am trying to advertise default route from GRT to MPBGP-EVPN but not able to do it properly with the following configruration. Thanks in advance for tips and correction **************************************...

uni1389_0-1766850713846.png
uni1389 by • Level 1
  • 748 Views
  • 11 replies
  • 0 Helpful votes

CBD network topology not right

Current SituationWe are encountering an issue with the network topology. The setup consists of 10 switches, all running firmware C1200-24P-4G and using the same model (C1200-24P-4G). These switches are organized into two clusters:Cluster 1: 7 switche...

GerwinH_0-1767001453665.png
Gerwin H by • Community Member
  • 93 Views
  • 0 replies
  • 0 Helpful votes

Resolved! ACI forwarding question:

ACI forwarding question: usually in a single pod when an endpoint wants to reach with in the same subnet but it dest not known it will send a spine proxy to one of the spines. And Spines check for the endpoint if not present it will drop it won't flo...

Resolved! Strange DHCP Behavior After Rebuilding Cisco WLC

rebuilt a wireless controller from scratch because the original one was damaged and there was no backup available.I’m currently facing an issue with DHCP. The corporate SSID is working, but clients connected to it are receiving an IP address from the...

athan1234 by • Level 4
  • 274 Views
  • 4 replies
  • 0 Helpful votes

FMC HA SECONDARY NODE IP CHANGE

I'm going to move my secondary FMC device to another physical location and i will change its ip address used in the HA configuration. so, i was planning to 1- break FMC HA  2- change FMC IP 3- configure HA again  what i expect that FTD will be manage...

Cisco U labs - copy and paste from instructions to VM?

My question is, in Cisco U labs, how does one copy and paste from instructions to the VM?I researched but not found a solution, hence I am here asking for input.Within a Lab within Cisco U training, how can you copy text from the side-bar instruction...

by • Not applicable
  • 124 Views
  • 1 replies
  • 0 Helpful votes

ACI with DMZ Servers

Hello Freindswith Regards to ACI with DMZ Servers can we provision the DMZ Servers (Web-DNS-Mail) directly on the ACI Fabric in Main Tenant aka(Production Tenant) instead of having Dedicated Tenant for DMZ Servicewe Already have PaloAlto at Internet ...

[12月31日结束] 思科社区 Connect & Grow 活动

 感谢大家积极参与并踊跃发帖支持 中日韩语社区 Connect & Grow 活动，第一波（Wave 1）获奖名单已出炉。第二波活动10月开启！ 恭喜各位获奖者！ （中日韩语社区联合奖项） ■ Wave 1 幸运新人奖： Keiyu Suzuki（日语社区） 中文社区获奖者 ■ 金奖：ChangJiang Li ■ 银奖：Rockyw ■ 铜奖：ilay ■ 管理员推荐：Sampson Luo  （日语社区 获奖者） ■ 金奖：Yuki Takahashi■ 银奖： Fumihiro...

EriMizuno_0-1748348295858.png FINAL.png
Load more