The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
I am currently working on a network setup involving two branches connected via a VTI VPN tunnel, as displayed in the attached topology. In the current configuration, static routes are used to facilitate connectivity between the branches.I’m consideri...
Hello,I am hoping to get some help in deploying HA with FTD 2140 devices. We recently upgraded to 7.4.2.1 (build30). Since the upgrade, the HA pair went into Active/Active and I have not been able to correct the issue. I forced the HA to break. When ...
I'm researching how to build a mesh securely, and some pages of Cisco itself puzzle me. Configure Mesh on Catalyst 9800 Wireless LAN Controllers - Cisco is one of the latest guides. It shows how to use local authentication and EAP-FAST on the control...
IntroduçãoNSLookupConfiguraçãoIP Name-ServerIP Domain-NamePAN Automatic FailoverFluxoDNS Cache Para obter uma cópia off-line ou impressa deste documento, basta escolher ⋮ Opções > Página Amigável para Impressora. Você pode então Imprimir > Impri...
I encountered this bug on firepower 1140 in ASA mode, OS version 9.16.4.62. But for me workaround didn't work. Only way to successfully show access-lists was through more system:/running_config command. Be aware, because I tried to fix this bug with ...
This lab setting is connected with a crossover cable but is still down. Please advise me Thanks.cisco 4331/Cisco IOS XE Software, Version 16.09.05controller T1 0/1/0framing esffdl bothclock source networklinecode b8zscablelength short 110channel-grou...
I need to replace my AR1001-X router because of coming EOL. They are used to peer with 2 different ISP's for redundancy. It is all non encrypted ISP traffic. The ISR 4461 shows the below throughout info using a boost license on unencrypted traffic of...
We migrated some Dell servers with Broadcom BCM57454 Server NIC connected to 93108TC-FX to Nexus 93108TC-FX3P. Same configuration in NXOS is in place with NXOS version the same on both switches with 10.3.6M.Some 10 Gigabit Cat6a connections does not ...
Gi1/1/1 Root FWD 20000 128.49 P2pPo1 Desg FWD 2000 128.2281 P2pboth are connected to the root bridge, which is a pair of 9500's. with each port connected to a different switch. G1/1/1 goes to core 1, with g1/1/2 going to core 2. trying...
Happy holidays to all community members!Over the weekend, I experienced a strange issue on CUC primary server. All the sudden, RTMT triggered high CPU usage alerts and CuGSuiteSyncSrv consumed 99% the resources.Processor load over configured threshol...
When booting and power cycling the complete 6 switch stack I noticed that what prior to the reboot switch 1 becomes lets say switch 5.Is there a way/command where switch 1 will always be switch 1, switch 2 will always be switch 2, and so on.I know th...
I have a probe that is incorrectly detecting two switches that do not actually exist for the company. These two switches are not even reporting to the same subnet as the probe. I have confirmed without a doubt that the switches CBD thinks are online ...
Hi all,I have a latency problem with the Exanic-X25.When I use Exanic-X25 SmartNIC 10G Firmware (provided by the Cisco), I got about 950ns latency. When I compile FDK "native_nic_example" with evaluation license for different versions, I got the foll...
Hello Community, According to the CML 2.7.2 Installation Guide ESXi 6.5 and later are supported hypervisors. I am running ESXi 6.5 on a Gen 7 Proliant DL380. Every single time I try to create the CML 2.7.2 VM from the CML 2.7.2 .ova I get two specifi...