Selecting DNA for Cataylist i was wondering if C1-ISE-BASE-T is the same as L-ISE-BSE-PLIC show in ISE licensing
Selecting DNA for Cataylist i was wondering if C1-ISE-BASE-T is the same as L-ISE-BSE-PLIC show in ISE licensing
Dear guysi am very confuse about new Cisco termi know, SDN in cisco is different for seperate sectionsfor example:SDN in WAN is SD-WANSDN in LAN is SD-AccessSDN in DC is ACIfor example in WAN we should to use vmanage, vsmart , ...but i dont know what...
Selecting DNA for Cataylist i was wondering if C1-ISE-BASE-T is the same as L-ISE-BSE-PLIC show in ISE licensing
Dear all, I have brought 2 cisco 9300 switch. Bieng new on this switch i want to know, is Network Essential and DNA License are pre installed on it or we need to activate it.
Hey All, Quick question. We have a pair of Cat 9500 border switches that are connected together at layer 3 to support an SDA fabric. We are looking to connect an ESXI host to the border switches using 2 x nics (dual homed) and determined that the bor...
Hello Community,I'm trying to re-image a 4331, i can only boot to rommoni try to tftp the image to the device but there is no tftpdnld optioncan anyone share how to do this on the 4300 router?
Hi All! We have a few projects that are looking to take advantage of the free DNA Appliance offer. These networks have yet to be implemented and there has been some concern about what will happen if the network connection between the switch and the ...
Hello, I can't seem to find decent information regarding this.DNAC can provision the underlay network, but i find no details on how it does so.Suppose i have a 3-level campus network: Access, Distribution, Core and Border nodes.The underlay deployed ...
Hello community, We are having troubles doing the DNA and ISE integration, when we add the ISE in the DNA center all looks good and the device show the "ACTIVE" state, but I never see the client in pxGrid services, so ISE nevers see the DNA center ...
Hi all,Recently, on my ASR9k appeared this error: device 'RAGNAR Daughter Board FPGA' detected the error 'Timestamp Block: framing error for decoder A'". I searched for the bug solution but did not get the result. Furthermore, I also don't understand...
We are integrating a third party device (AnyRover from AnyWeb). The AnyRover appears in the inventory and in the topology. However, in the topology the link between the AnyRover and the connecting Switch isn't shown. LLDP is turned on on both devices...
We have a Win2013 DHCP server, and the WAP571 connected to an unmanaged switch on a flat network (no vlan). Using the wizard on the WAP571, there is now 2x SSIDs setup. However, there is no option to allow the AP the DHCP relay. Cell phone and lapt...
Hi all, So I have a stack of 2 x Catalyst 9300 and 2 x C9300-DNA-E-48= licenses.I'm a bit confused on how to activate these licenses. Everything clear with the old ones, but the new versions, are just RTU ? Thanks,N
Hi, Is it possible to focus reports based on a particular location or certain WLC? We're a global organisation and i just want to run a lot of reports just based on my region/location or WLCs. It seems difficult to find how to modify the reporting ...
Is there a way to reset a DNA Center appliance to "factory defaults" ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-17-2024 05:28 AM | ||
10-10-2024 10:25 AM | ||
10-10-2024 05:44 AM | ||
10-09-2024 07:02 AM | ||
10-08-2024 07:20 AM |
User | Count |
---|---|
4 | |
2 | |
1 | |
1 | |
1 |