Hi I am trying to create a QOS policy. I add one and name it and leave everything on the defaults (CVD Queuing Profile etc) then add some buildings to the site scope. When I then try and deploy or save as draft I get the following error: Error Saving...
Forum Posts
Resolved! Application health DNA
Hi Guys, I am looking at purchasing DNA and giving a business case to do it. I have several switches already with DNA essentials/network essentials the switches and they are non-SDA. (1) Firstly to use application health I believe it is available wit...
Hello Community!Can anyone tell me about CBAR and how does it work in DNA Center. I know that it is a Controller-based App classifcation. Actually I want to monitor Skype and ms Teams. I added them using Application Visiblity and I want them to appea...
Hi all,i know about application policies in DNA Center but is there an option for applying QoS policies to prioritize all traffic sourced from a specific ip pool? Also, any option without taking advantage of automation in DNA Center?Thanks in advance...
Hi,I would like to validate what is the expected behavior of Cisco DNAC when an AP that receives an IP address via DHCP changes to a new IP address?Note: DNAC added AP to inventory after I discovered and provisioned the WLC.
Hello Cisco community. My organization is set on reloading our access switches annually and I'm tasked with determining a way to ensure this is done. I have used Cisco Prime to run a job using the CLI templates available there and am looking for a wa...
I have made some simple templates that should configure dot1x on userdefined ports. But when I try to provision the template, either to the device or just to preview I get an #Conflict error in the CLI output. Running DNAC 2.3.5.5 on Cat9300 on IOS 1...
Hello, We have a 2nd generation DNA center appliance DN2-HW-APL-L which was connected with a 1GB SFP on the enterprise and cluster ports. We replaced the SFPs for a SFP-10G-SR-S and now such SFPs are not even showing lights on the LEDs, they have com...
Hi All,I have a scan of vulnerabilities (Qualys) on my network that detected TLS version 1.1 running on DNA Center on ports TCP 443 and 9005.My DNA Center is a 3 node cluster running version 2.3.3.7-72328-HF5I've disabled following this instruction: ...
Hey brains trust,Finally got my hands on a DNA vAppliance!I've got 50+ ISR1100 router and wanting to push a image update to these devices.Issue I have is DNA is within our internal network 10.1.x.x and the ISRs are managed via their public IP address...
We currently using the on-premises version DNA on M4 servers, they will be EOL mid 2024. We want to replace them with the Vmware VAWe already received and installed the VM version successfully . Does someone knows the roadmap for the migrate capabili...
Hi,I have config archive configured, see below, it is showing as connected: But there are no files in the directory:Are there ways to verify on DNAC if files are transferred?CheersIain
Hi Guys, I have a DNAC dr 2 node setup on 2.2.3.5 and one of the nodes failed due to a memory issue. It failed to the secondary but the main site was frozen for about a week. I have tried to re-join the cluster and also pause the cluster but i get ...
現在Prime Infrastractureを導入しているお客様がおり、DNA Centerへのリプレイスを検討しています。PI利用は東京なのですが、大阪のメンバーがコンバート検証を行おうとしています。検証DNA Centerがインターネット接続できる状態であれば大阪側でも対応は可能、の認識で間違いないでしょうか。
Resolved! Remove One server from cluster
i have DNAC cluster . i have one server has hard disk failure. so after replace hard disk , shall i remove server from cluster and re-image it again. if yes , how to remove server from cluster and add it again
