Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 23, 2024 through Friday, October 4, 2024. Our colleagues Arpita Dash, Prateek Upadhyay and Udhay R. will be waiting to...
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 23, 2024 through Friday, October 4, 2024. Our colleagues Arpita Dash, Prateek Upadhyay and Udhay R. will be waiting to...
Hi, DNAC Product:DN2-HW-APL-U Appliances installed and done the basic setup. we got the error called SSD life time lapse. Severe fault is showing. please suggest.
Does anybody know? Which way can I set the golden image through tag only?I have some switches / routers and I need to set for some of them ios version 17.06.05 and 17.09.02 for the routers, I set special tag on the ios - C9300-17.06.05 and ISR4331-17...
Dear Concern, We have purchased cisco DNA Appliance DN2-HW-APL. When we power on the device we found hard disk error. We updated the CIMC bios and then hard disk error has resolved. We noticed there was no DNAC IOS. We download the IOS and tried to...
When we try to deploy c3650 switch as edge in DNAC it ended up the error as follows:"NCSO20544: Failed to add device L04-IDF04-FE02-TEMP.domain.com to fabric. Only Cisco Catalyst 9000 Series Switches support Layer 2 Pools." DNAC version: 2.2.3.4 swi...
Hi, please may you tell me if it is possibile and if it is a supported solution by Cisco to use iBGP session(s) instead of eBGP between Border Nodes and the Fusion router for IP Transit ?Shortly: Fusion Router and Border Router can be in the same BGP...
HmmAdded a CLI credential in Management Credentials and signed it to Global. Bad idea.I want to be able to use it on specific sites. Not Globaly....But in Management Credentials its grayed and cant be deleted just edited AaaaahhAny ideas???
Dear Friends,As shown in the attached picture, I have the SDA network configured.My goal is to remove the distribution switch connected to SITE-A CO1 & CO2 and migrate the Admin building G Floor and Floor-1 edge switches to SITE-B CO1 & CO2.My doubts...
Hi!Im using a remote host to store all my backup data of my dna center, after a reset I did to the dnac I cant see any backups on the backup tab (system->backup and restore->backups).I have daily scheduled backup and everytime it finishes with succes...
We tried to provision a switch through LAN Automation and we receiveid this error: "Perform write-erase and reload on PNP device TSPXXXXXXXXX after resolving device issue. Please delete this device from PNP page to retry PNP onboarding." Switch 9200-...
The DNA server is connected to the smart account and registered. My network devices do not have a direct connection to the Internet. I'm trying to change the SSM connection mode to "smart proxy". In the audit logs, I can see that the changes are bein...
Hi,I have noticed that during Image Update Readiness Check the config register check it is showing the warning for config register values. As below:Please change the Config-register valueExpected: 0x2102,0x102 Actual: 0x142 (will be 0x102 at next rel...
We need to allow guest wifi users access to internal webmail. I can create a loopback easily, and this works for most clients. We are having an issue with android though due to its use of DoT (DNS over TLS). This occurs on port 853 and does not trigg...
Hi, Currently we have a CORP SSID in our network and are hosted on 3rd party Wireless controller, now we have a requirement to extend that SSID to the SD fabric over the LAN. We are using a Wireless over the top so is there a way to extend this vlan/...
Hi All, Is L2/L3 port channel supported in C9200 with Network/DNA essential license? #sh ver | in Smart Licensenetwork-essentials Smart License network-essentialsdna-essentials Subscription Smart License dna-essentialsAlso with this license can I con...
Management bought some Audio Visual devices that support bonjour/mdns and we are expected to make airplay work.In the below setup AP and A/V device may end up connecting to same switches but because of signal overlap, client can remain associated to...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-17-2024 01:45 PM | ||
09-11-2024 06:36 AM | ||
09-10-2024 01:11 AM | ||
09-09-2024 07:23 AM | ||
08-21-2024 03:14 AM |
User | Count |
---|---|
3 | |
2 | |
2 | |
2 | |
1 |