Dears i have 2 ISR4331 Routers with 40 Subinterfaces and i connected both routers to the Switch 3750 i connect my laptop to for example vlan 2 and give it from vlan2 IP range then i tried to ping the VIP it connect , then when i change the Vlan to an...
Forum Posts
Hi, I have two C9500 X16. I need to make them as one by using stackwise virtual. But I having issue to stacking them: 1. It detect dual active and block the virtual link port. 2. One of the switch become recovery mode. Im connecting both switch w...
Hello All, My doubt is in regarding the selection of DR/BDR in OSPF. In the above scenario: 1. Lets say R0 with router id:10.10.10.1 is configured first followed R1 with router id: 10.10.10.2. 2. The interfaces are in Area 0. Question: Why d...
Hello experts! This is my first post, so go easy on me ! I have a 3850x switch with 10gb connection for all my outbound traffic and 1 gb connections going to all my sites. My 3850x is doing all the routing to the outside though the 10gb connection...
Version: DNS-Server#show verCisco IOS Software, 7200 Software (C7200-ADVENTERPRISEK9_SNA-M), Version 15.2(4)M11, RELEASE SOFTWARE (fc2DNS6, )Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2016 by Cisco Systems, Inc.Compiled Sun...
All, Saw a strange issue with a port channel configuration on two stacked (SVL) 3850's. I suspect someone initially configured the port channel incorrectly, and now I cannot use that same number for a port channel group even if I delete it. I have ...
I had to expand our management subnet and need to update the related vlan interface configurations with the new mask. Ive been looking for a way to change just the mask without having to reconfigure the IP address so I can script the update throughou...
Hello, I currently have a Cisco ASA 5506 I'm swapping out with an older 5505 that's having issues. That being said I've essentially copied the config for the most part from the old one to the new one. What I'm currently running into is an issue w...
Hello, We have a GETVPN domain running 30 routers with 3 Key Servers in COOP mode. During a change yesterday we changed the crypto ACL on the Key Servers to add the following: (Legacy deny (do not encrypt) statements output omitted) access-list...
Hi I'm doing this.. Build the following network using the following IP Addressing scheme: 1) Network address 192.168.100.0/24; host addressing requirement: 58 for 2 subnets; VLAN 10 to host IT Group. 2) Network address 209.165.200.0/24; host address...
How to configure snmp in a cisco switch to use the object name instead of the OID? The idea is to set and get parameters for the interfaces of a switch using expresing like ifAlias and ifAdminStatus insted of the OIDs. What do i need to configure i...
Hello, I am looking for the behaviour of extended ACL, including layer 4 / port informations, in the presence of fragmented IP frames. It seems to be different depending on the use of the ACL, as follows: - when used in an access-group, layer 4 infor...
Hello, I am trying to set up a layer 2 bridge between a router port and a switched port on a 4321 router, running X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S5. The switched port is located on a NIM-ES2-8 module. The router port is native. This...
Hi ; Can we enable type-8 or type-9 passwords on cisco Nexus switches, i can see the max type supported on my nexus is type-5. I want to create a local database of username and passwords on switches.
Hi, I need to make a custom report for data replication from Informix to Sql Server. I need to provide the details of Primary UCCX side in the Data Connection but the problem is, there is no detail of PUB or SUB node at the database level. The on...
