the uplink ports in N9K-C93108TC-EX work at 1G?
the uplink ports in N9K-C93108TC-EX work at 1G?
I have a N9K-C93180YC-EX & i am trying to bring up a connection to a C9500-24Y4C switch. Tested connection with 10Gbps SFP's no problem, but when using a pair of SFP-10/25G-CSR-S SFP's & can't get the link to come up. I have tested the fibre patch l...
Hi everyone, I need a clarification about extend Layer 2 Domain between two datacenter. I Have DC1 and DC2 with 2 nexus5548UP ad core layer dc, I can use a 2 ring DWDM connectivity between two DC. I would like to propose a VPC double sided : DC1:2 ne...
I have completed CCIE DC Lab, now want to give written exam to retain my CCIE number. Planning to give below security paper. Is it right to give this one, I am having doubt hence posting this message.350-701 Implementing and Operating Cisco Security ...
Hi Folks- I have a few N7706 and N7710 Switches in which I need to upgrade the NXOS code from 8.2(1) to 8.2(6). I'd like to do the upgrade via ISSU but want to ensure I avoid any problem issues etc. Looking for any recommendations/guidance on doing u...
Hello together, I would like to connect a Cisco Nexus 5010 to a Cisco 5020 with port channel and vpc.I set up channel-group xx mode active on the Cisco Nexus 5010 ethernet interfaces and on the Cisco Nexus 5020 on the Ethernet interfaces channel-grou...
Dear all, I would just like to configure 1Gbps Output Shaping on Neuxs93180-YC-FX. Before I have confirmed the QoS Traffic Shaping on Neuxs9372TX-E like the following configuration howeverif I configures on Nexus93180YC-FX it shows the following outp...
I've been reading the following document:https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/118997-technote-nexus-00.html I would like to peer a pair of firewalls over vPC with OSPF to a pair of Nexus 9ks, I'm happy with this and I see that the...
Hi Team, We are facing issue in Nexus 9504 switch Module-28 SUP replacement.After replace with RMA it's showing "Powered UP mode" not in standby mode.We try reboot of module 28 multiple time. But show same mode "Powered UP mode".Note:- 1. Active SUP-...
Hi all, i have attached a file here where it shows a simplified diagram for my DC. my issue is VM2-Site_2(red) is able to talk to VM1-Site_1(red), but VM-Site_2(blue) is not able to talk to VM1-Site_1(red). -- keep in mind, this is not ACI, i am co...
Hello, We are implementing VXLAN BGP EVPN in our Datacenter. Our VXLAN Fabric consists of two Nexus 9364c Switches (Spines) and four Nexus C93108TC Switches (Leafs). The Leaf switches are forming two pairs of vPC VTEP Switches (Leaf1 with Leaf2) and...
Hi expert I would like to know whether it is necessary to purchase NX-OS Essentials/Advantage license for Nexus 9300?I just want to use it for basic connectivity
Hi Team , Without removing the config mode access how can we prevent someone from entering into config mode ?Can you please share some idea's ? Requirement :L1 team got access to config mode , but we don't want them to enter into config mode and run...
Greetings Community, I hope to get some details from the BU who developed Tetration, ACI, and the N9K... I have a philosophical question based on the ability of accessing switching services of say a Nexus switch (N9K or 93180-YC participating in eith...
HI Inhave just rebooted a pair of 9300 switches and now its showing type 2 inconsistency check not performed. I have double checked the complete config and theres not inconsistency. Any idea what might be causing this?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-26-2024 06:41 AM | ||
06-14-2024 10:59 AM | ||
06-14-2024 06:10 AM | ||
06-12-2024 07:09 AM | ||
06-05-2024 03:06 AM |