Dear Cisco.Greetings...! We have a CISCO FPR 2110 firewall.Does it supports 'Dual internal LAN' configuration without a router. Example: ASA 5505 need a router between every different networks. Can you please let us know asap. Regards,Sai Kumar
Hello Folks, I am going to export 1 office location from one PI and wanna import map archive and bulk APs for this office in to the other PI. Can anybody advise if I can import a Maps for specific office location (1 site) only? I do not wanna overwri...
I've been out of school for about 2 years. I got my CompTIA A+ hoping to get an entry level job but so far no luck, so recently i've been interested in getting my Associates Degree. Browsing my local community college I stumbled across the Cisco Netw...
Hi All, I hope someone can help with my issue, I'm trying to setup my cisco business dashboard and Probe. However on my probe ui after i redirected on the Dashboard and select create or associate network and then i click the finished button and redir...
Hi,i am trying to form a HA between a primary and secondary server , both of the them are exactly the same software and patch version, but when i am trying to establish a manual failover it fails with result: Error(s): You must correct the following...
I have a router 2811, and PC connected to fa0/1. It cannot receive ip address from router. It should receive from pool 50 (vlan50). Patg#sh run
Building configuration...
Current configuration : 1693 bytes
!
version 12.4
no service timestamps l...
Hi all, I need some help w.r.t setting up VLAN maps/ACL. The following scenario is what I need:Three VLANs - VLAN10, VLAN20, VLAN30VLAN10 - Should be able to access all packets on VLAN20 and VLAN 30VLAN20 - Should only be able to access VLAN10VLAN30 ...
Hello!I'm try to update WS-C3650-24TS (stack with 2 switches) from 03.07.04E to Denali 16.3.8That's what i did:1.Download Denali 16.3.8 from cisco.com2. Execute software clean command on the stack and delete all unnecessary files.3. Copy new ios to f...
Hi, consider you have these SVI's:VLAN 10VLAN 20VLAN 30 How do you allow devices e.g. in VLAN 20 to connect to a switch with SSH, but disallow devices from other VLANs to establish a SSH connection?
Hello, I recently installed Cisco Prime Infrastructure 3.5 so as to manage catalyst 2k, 9200 and 9500 then upgrade to Prime Infrastructure 3.6 to support 9500 switches. It appears that Catalyst 2k and Catalyst 9200 are managed correctly and 9500 is s...
Hello,I've been trying to find a way to suppress SSH syslog messages for a specific user on our ASR9K platform. Example: %SECURITY-SSHD-6-INFO_SUCCESS : Successfully authenticated user 'x'%SECURITY-SSHD-6-INFO_USER_LOGOUT : User 'x' So far, the only ...
Good morning, Actually i have a switch with Cisco release: cat3k_caa-universalk9.16.06.05 on install mode. I need to upgrade with release:16.06.08 but i can't reload the switch at the end of the process. Is it possible to postpone the reload of the d...
HelloWould you please tell me how can I change Cisco 3560E interface IP/GW without discounting from switch ?This switch is far away from me and I should change interface IP and default gateway to another range.Thanks
I want to connect different segments of CCTV (DVRs/NVRs) using WAP150 Radio.Can somebody advise on the configuration.I would like to have point to point links between each segment.
I have a 4431 ISR that I recently upgraded to the 16.12.2r ROMMON and now it is stuck in a recycling loop that creates loads and loads of dump files that will not allow the IOS to boot the device normally. I have tried changing the CONFREG boot opti...
