I'm trying to restrict access to the management interface of a pair of 1150s running 7.2.0. I've run the following command: configure ssh-access-list 8.8.8.8/32 which appears to complete successfully("The ssh access list was changed successfully."...
Forum Posts
Resolved! ASA5510/ asdm compatibility
Hello everybodyI lost asdm523.bin image for asa723 and i couldn't find link to download it can anyone give me the link to download or ASDM compatible for asa723.thank you.
Hi, Everyone:After done some troubleshooting and data capture, and found out Intrusion event syslog for message ID 430001 is sending to destination port (udp 514), I could see other message ID (430002, and 430003) are sending to udp port 1515, since ...
Hi Im tasked to move an HA 4115 FTD to a new FMC. We are going from Physical to Virtual so sadly this does not comply with the supported fmc model migration path shown here: https://www.cisco.com/c/en/us/td/docs/security/firepower/fmc_model_migration...
Take a look at packet-tracer below. I have scrubbed some IPs and names for simplicity and privacy. Are you able to confirm based on the output which rule is allowing the 1.1.1.1 traffic to 2.2.2.2 in through the Outside interface? Basically trying t...
Hello Everyone, Very often as Network Administrator there is a need to save the ACP on the Firepower Management Center(FMC) as CSV, while the FMC in itself supports the policy import and export option as a full-fledged feature there is no way to save...
I understand that setting of ACL is not necessary when traffics go through high to low on the ASA, and communication is possible. However, when communicating from INSIDE to DMZ, I want to restrict accessing the server in DMZ, so I configure deny ACL ...
I am wondering if anyone else is running into this issue where Firepower is blocking archive files. It seems there is a bug that has been around for 10 versions of the software. Symptom: When transmitting an archive (GZ, ZIP, etc.) through a Firepowe...
Hi team, following this discussion that already close : https://community.cisco.com/t5/network-security/cisco-fmcv-7-0-5-cant-be-access-with-gui-and-ssh/m-p/4783611#M1098217 ==> Summary : FMCv experiencing 100% CPU & Memory, but after reload the FMCv...
Resolved! FMC 2600 CLI Denied Access
Hi everyone, I got FMC 2600 v6.6.1 (build91) the users are created normally in System > Configuration > Users, the account has no problem in accessing FMC GUI, but in CLI it can not access, always showing "Access Denied" even though we key-in correct...
I'm hoping someone on here has ran into a similar issue as us with trying to log all permitted and denied traffic for RAVPN traffic on FTDs.We recently migrated from ASA to FTD and have had trouble with getting all of the logs we'd like to see on our...
If there's an attacker on a public LAN like a school or a shopping centre for example, the adminstators can look at the router's packet capture and see the attackers MAC and IP addresses, but what can they do with this information to figure out who t...
I am having issues with a user based rule for an ACL. The rule should permit users to access certain URLs that are otherwise blocked. The rule does not currently permit users access as it should. This FMC was recently patched to Version 7.0.4 (Build ...
please can anyone list the steps on how to change the ip addresses subnet of my current fmc and 2 ftd in ha? I have read that in fmc 6.5 changing ip can be done in the GUI but im not sure of the steps on how to do the whole thing
Resolved! FXOS Query
I am new to FPR and have a few queries.How do I find out the current FXOS version? Is there an upgrade for FXOS, how do I do the FXOS upgrade?
