Hello AllA rather basic enquiry but a frustrating one.I am trying to allow a hide-nat host out to the Z-Scaler Range, all subnets within the range has access to the Z-Scaler Zen, apart from 1 host. I am in a position where I am unable to disable thi...
Forum Posts
hi,i got a pair of ASA FW in active-standby setup each in a different building.we're closing one of the building/rack and plan is to bring the primary-active FW to the next building where secondary-standby FW is installed.is there a "safe" way of cha...
Resolved! Unable to exclude host from QoS Policy
We have a 4110 Firepower running 7.0.2 managed by FMCv also running 7.0.2. We've had a couple recent events where Adobe released updates and our Internet bandwidth was impacted. An update server has been created, so I'm trying to exclude this server ...
After I upgrade new firmware(ftd-fp2k.6.6.7-223.zip),I can not log in firepower with username and password default.Are there somebody can help me?FTD loading so long and after that it reboot ,reboot so many times.Now I cannot log in to the device. Wh...
Dear Support Communityi wanted to know if someone knows how to change the Timezone for a Firepower 2130 managed locally by FDM, we're using version 7.0.4. On the time settings we only can set the NTP servers, but no timezone. Also tried with Flexconf...
I have 2 brand new fp-1140-asa appliances, MGMT ports get IPs via DHCP. Console ports are connected to our known working console server (9600-8-N-1) and I can't get into this box on either. MGMT IP https gives me the ASDM page and I have tried all...
Hello, I am getting these errors on the firewall and am not 100% sure how to resolve them. Any help on this would be great! Thank you in advance. ModelSoftware VersionOS Cisco Firepower Management Center 16007.0.2 (build 88)Cisco Firepower Extensibl...
Does anyone know why the iPhone's certificate is not trusted (see attached) image. There is no error in Cisco ISE's live log but did see a message in ISE under the certificate section saying that this certificate is NOT used to verify the authentici...
We currently have two ASA 5515x's in an Active/Standby failover setup that we will be migrating to the same failover setup with two 1140 FTDs. I see there is a Migration tool for converting the ASA config to FTD. From an install perspective is there ...
FTD running version 7.2.0.1I have several FTD, and collecting SNMP from a FTD located inhouse, from "inside" interface, works fine.(I use SNMP v3) from this guide "Document ID:216551"But when I try to get SNMP data from a FTD (site to site connected)...
Does anyone know why the iPhones are not trusting the CA certificate when issued by Intune? The client already has the the CA (Microsoft) as a trusted root. ISE is passing both the server cert and root cert at the same time and then client closes c...
- Take care ! : https://www.cisco.com/c/en/us/support/docs/field-notices/725/fn72501.html https://www.cisco.com/c/en/us/support/docs/field-notices/724/fn72483.html https://www.cisco.com/c/en/us/support...
Hello all,Hope anyone can help for this request, i'm trying to export event logs from FMC to get csv file. Is there any way to get help for it?Thanks much.
Resolved! CISCO FIREWALL
hello Everyone,I need to purchase a firewall for our vessel in the field, it's a small network with internet access. please I need your recommendations on what the cisco ASA is to be purchased.Thank you all
Hi friends I have deployed several FTDs in the network, but there is a problem with registering these FTDs through the internal network. Routing information and firewall ACL need to be configured. What is the IP address of the relevant CSSM registrat...
