i can't find any document showing the memory capacity of the cisco ips 4250 and any upgrading capabilities
i can't find any document showing the memory capacity of the cisco ips 4250 and any upgrading capabilities
Hi,,I am having pix 515E with 7.0.2 os. I configured policy based nat and applied on the nat (inside) 1 access-list (access-list name)with global (outside) 1 interface command. The network diagram as follows.L3 switch-->pix 515E--->router 1700In L3 i...
after an password recovery the pix is not using the startup-config anymore. The running-config is taken from an other file which i dont know.Write mem command does add changes to the startup-config but after power off/on the running-config is again t...
Hi,I'm trying to configure a Pix 506E for a single network to allow RDP to the server. The Pix outside interface is a public IP that conects to a router managed by AT&T. The Ip address is 12.146.x.x. The inside interface is set to 192.168.1.1. To all...
Hi am running a pix 506 3.6(3) to gain Internet access to my remote office users. And in the same time users are connected to the main office via Lan to Lan ipsec tunnel. The pix is connected to the Internet with ADSL line (ISP). The pix is also dis...
I've scoured the Cisco site and could not find the tool to migrate PIX to ASA. I have a 515E (6.30 code) and I want to use the "migration tool" to do the migration to an ASA 5520. Is there such a thing? Thanks,Damien
Hi Expert,If I want to Dynamic NAT port range from 5500 to 5800, into my public IP which NAT to a private IP, how to configure?Here the example,public IP = x.x.x.xprivate IP = z.z.z.zNAT x.x.x.x port 5500-5800 to z.z.z.z port 5500-5800The PIX firewal...
Hi All Expert,Can anyone help if I need to simulate an attack to a server on DMZ zone.How to know there is an attack to that particular server and how to generate the attack?Really appreciate for help on this.Thank you.Rgds,Au Yeong Shaw Voel
We use VMS 2.3 with RME 3.5. For RME no support for 876 routers is available. Will there be a IDU Upgrade file for the RME 3.5 that covers the 876 in the near future?
After upgrade to PIX 7.1.1, some reason PIX freeze the traffic for at least 5min when very large amount of data going from inside interface to DMZ interface. However, DMZ interface has VLAN configure. Did any of you come of cross this problem.Any he...
Just trying to forward a port from outside Int->device sitting on "inside" Interface, but getting the following in the logs:%PIX-2-106006: Deny inbound UDP from 66.21.215.238/50507 to client_routable_address/6881 on interface outside%PIX-2-106006: De...
I have a IDS sensor running 3.1 version of soft ware. I also have a upgrade / recovery cd for version 4.1.When i load the cd & boot the machine it stops the installation & starts looking for a system file. Is it possible to upgrade from 3.1 to 4.1 st...
I have a 2000 server that offers MRI images to remote clients. From this site I have a vpn useing a pix at the remote.Telnet, Ping, and http works, sending images does not, I suspect this is an MTU issue, do I need to change the MTU at both the host...
Could you explain me ? management-only ? I think no ) where can I read or explain me pls )
We had an instance of OWA setup through our old PIX that would allow users to use it through the Internet, rather than having to login through VPN and then accessing it.Turns out having to login through VPN and accessing OWA is not a desirable option...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-19-2024 09:48 AM | ||
08-19-2024 03:53 AM | ||
08-14-2024 08:06 AM | ||
08-08-2024 06:44 PM | ||
08-08-2024 06:24 AM |
User | Count |
---|---|
8 | |
7 | |
4 | |
2 | |
1 |