Other Network Architecture Subjects

I need to get my Steel Belted Radius Server to Assign Framed IP Addresses to my AS5350, Currently the Radius Server assigns Framed Addresses to a 3Com Total Contro NAS. Any ideas on the commands and etc, I have the attribute 8 in access request confi...

Does anyone know if it possible to use the UTLite component of User Tracking to send the users details to two separate Ciscoworks servers without running UTLite twice?

What is the benefits of using a Radius server with the BBSM. On my last installation of the BBSM as long as the user agreed to the terms of usage their rooms were billed for daily usage. Is the Radius setup for customers be billed on a minute/hourl...

I've got 2 devices on a 3500XL access switch and need to give one of them higher priority than the other. The device in question is sending a steady video stream at about 5.5Mbit/s and I'd like these packets to take priority over the other device whi...

Hi I have Cisco 3660 with analogue modem (NM-8AM-V2) as RAS, when i connect over PSTN the speed is always under 33,6K. also when i type show modem configuration i see the max speed 33,6can someone help how to avtivate V90/92 on this modemthx

I have 2 Point-to-Point T-1's with OSPF, and Perpacket load sharing. When I do a large file copy over the circuits I cant get it to use the full circuit anylonger, unless I do 3-4 large coppies. It used to max both circuits just fine with one copy ...

Dear I've a igx run rout of LCON resources . I'm unable to add more connection . My IGXs use NPM-32 card . When i use the 'dlcon' command . It show LCON 2750/2750 (used/totals). How can I add more LCON ?. I found NPM-64B can support up to 3500 L...

I have a request and I will simplyfy it below :)SCENARIO :-I have a router and two LANs. Host-a on LANa sends too much traffic to a server-b on LANb. The two LANs have other client/server apps which are suffering because of of the host-a/server-b t...

Cisco's best practices document for Catalyst 6500/6000 switches (doc id:24330) states that auto-negotiation is "required" for Gigabit connections, not for speed negotiation but for "flow-control parameters, remote fault information, and duplex infor...

I have a network of about 21 cat4006 and Cat4003 running ver 6.1(1) and 4.5(13a). All these cats are connected to 6509 throught gig links that are trunked. I have never seen a flapping problem until we deployed wireless AP350. Most of the Voice and d...

Hey All,I need some input on a better way to accomplish something. Here is the situation: I have WAN with 80+ sites all sites using cisco 2501 or 2600 series routers. Currently there is on average 20 users at each site with mail and file servers at t...

I have a 3700 series and I want to take incomming packets on port 0/0 and forward them outbound through port 0/1. I thought this would be considered tcp/ip forwarding or port bridging but I can't find any guidence in my "cisco field manual: router c...

Is there any mechanism to configure an 837 to only allow access from one host device (one MAC address)?

Hi folks,first we have installed Cisco Works 2000 - 3er Edition without the Campus Manager. Now we made an update to Common Services 2.2. All is well done, but the Campus Manager isn´t available (although we installed the Campus Manager CD) We tried ...

I'm receiving a huge amount of runt packets on some switchports, they come up as Receive Errors.The switch is a 2950-24 and all of the interfaces/workstations are hardcoded to 10Meg Half duplex.My sniffer doesn't show any sign of runt packets.If I ch...