The "F" may appear in different position on every boot:Power-on-self-test for Module 1: WS-X4013Status: (. = Pass, F = Fail)uplink port 1: F uplink port 2: F eobc port: .processor: . cpu sdram: . rtc: .eprom: . ...
The "F" may appear in different position on every boot:Power-on-self-test for Module 1: WS-X4013Status: (. = Pass, F = Fail)uplink port 1: F uplink port 2: F eobc port: .processor: . cpu sdram: . rtc: .eprom: . ...
Can anyone tell me why this configuration does not work?All I am trying to do is rate-limit traffic on a port (any traffic)I can do it using storm control, but i dont want to use this as it has drawbacks.mls qos!class-map match-all port13 match any!...
I am no router guru. I used cofigmaker (yes everyone can now grumble) to set up a 1720 router to provide NAT on the ethernet side to my one public IP number. It is working perfectly for internet access. I have this hooked to a T-1 using HDLC at my...
Hi I run one production CiscoWorks server with LMS 2.2 on solaris 2.8. Now I have installed an identically standby server. I want to make the standby server to be a copy of the production server (user data,device groups, netconfig user templates and ...
Currently our ISP injects a defualt route into our IGP using OSPF. Due to plans to migrate to AT&T's IPFR service, our IGP will be replaced by BGP. I've been simulating the new environment in a lab and have run into an issue with the default route ...
Hi,I will be migration my network from ATM backbone to GE backbone. The migration will be in phases. Just want to get some advise from some experience people out there what are the things to be take noteThanks
Greetings,I'm trying to limit what DFM sends via the mail adapter. I've modified the mail_notify.conf file as follows trying to remove some unwanted traps: GA_ChoiceSubscription::Device_Down { className = ".*" ins...
We're running LMS 2.1 on W2K server and would like to send the fatal errors from the DFM to our cell phones. We are running Novel's GroupWise mail system and I was wondering if there's a documentation on how to configure the mail server field for se...
HiI need to make a simple PBR but it just don't seem to work. Let me brief you... I have router with a default route to another router connected to the internet, however i want that one host (192.168.127.2) jump to other router (think it like a rudim...
Hello I have a pretty simple internet connection that supplies access for 2 PCs.The downstream bandwidth is 500KThe upstream bandwidth is 256KI want to restrict each PC to have 250K download speed, and 125K upload speed. But maybe be able to allocate...
I currently have a port-channel set up between a 6509 and a 3550. VTP runs over this channel as well. We currently have 10 vlans, however only 2 of these will need to be configured on the 3550 switch. So I would like to do some VTP prunning to keep t...
Hi all:Is Cisco's implementation of MSTP/RSTP compliant with the IEEE Specs (802.1s/w) ? If now, how does it differ?Any help is appreciated.Thanks,Vishal
At what minimum voltage level will the switches (3524) and the routers 3640's reboot ?
Somebody knows about support for 50/125 fiber optic on Cisco 7206VXR with PA-A3-OC3MM?
Current Configuration: 3COM switches with 100MB Mutlimode fiber modules.New Installation: 2950 switch with 1000BASE-SX GBIC (Multimode) module.Question: Can these two fiber modules communicate on the same network?Thanks!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |