Other Network Architecture Subjects

Hi All,We have PIX Firewall 515E connected between Intenet and LAN. I have done natting on this firewall for Intenet Access.Now the problem is everything(Traffic) has got the same priority. I would like to implement Traffic Prioritization on this. Ca...

Ok, you guys have been soooo helpful for me so far. I recently was told to network two cisco 1721 routers for 56k frame-relay, but the routers had t1 wics, not 56k. Now we have 56k wics, but I'm having trouble seeing both router interfaces after con...

My first question is that is it possible to migrate from Windows 2000 to Solaris ? We have installed the CNR version 6.0.3 on SUN Solaris and it is up and running. We have tried to migrate the database from Windows 2000 to Solaris as per the instruct...

Hello,I am working on a special remote access issue (remote access MPLS/VPN), I configured the router with a virtual-profile and a virtual-template, and also I am using a RADIUS server that will provide the users an IP address, so I am using a the RA...

Does the latest version of CiscoWorks support SNMP Version 3.

The access to Internet from our company is ensure by a proxy server connected to a Cisco 3640 router. This router has directly connectivity to our ISP through 100Mbps link, but from the ISP our bandwidth is limited on 4 Mbps. How can I configure QoS ...

I have 6509 supervisor-1a-2GE with MSFC1 and want to upgrade the MSFC code to 12.1(19)E1a.- supervisor-1a-2GE=16M bootflash, 64M DRAM- MSFC1=16M bootflash, 128M DRAM.I found the release note of 12.1(19)E1a require 16M bootflash and 128M DRAM. 16M is ...

Hi All,I need to monitor cisco routers and voice gateways from a remote machine ... this is actually an ip telephony setup.I am new to NMS. Can you please suggest me some sources where i can find some basic information about it.Thanks & Regards,Manoj

Sorry for the basic nature of my question- I don't get to dip into routing too much, to Cisco's credit.I have a remote school site connected to my LAN with a Cisco 2621 (at their end), and a Cisco 3600 at my end. At my end we are connected through t...

IOS version 12.2(15)T8 only allows for squeezing a slot. I deleted an older IOS image out of flash and want to reclaim the used space but 'squeeze flash' or 'squeeze flash:' doesn't work.Any suggestions?

Hell to all, I have a challenge of tunneling multiple IPX networks through a PIX 506E 6.3(3) to/from 2 outside networks connected to us via private line T-1s. Currently we have at least 5 IPX networks running internally that go to one of the outsid...

Hi all,heres something really fuzzy....I have a /30 subnet with 2 usable ips (152.122.132.33 and 34), 1 network ip (152.122.132.32) and 1 broadcast ip (152.122.132.35). I am able to telnet my network ip (152.122.132.32) and get into the router having...

We have a point to point link IPLC Line between two locations and we upgraded from 512k to 1Mb and to 2Mb but the pinging time to between one location to other always remains the same. It was 260Msec when the link speed was 512k and then to 1Mb and n...

Is there a way to route appletalk accross multiple VLANS on a Catalyst 3550? Is there a 3550 image that supports appletalk routing?

Hi, i am trying to apply a rate-limit on a cisco2950switch interface.although the switch is accepting the commands, the rate-limit does not register any hits.Can anybody suggest as to whether rate-limiting works on cisco 2950 l2 switch and if it does...