I want to be able to enter comments before each output for the show commands listed in the list in my Python script. For instance, before the 'show ip int br' output is displayed I would like it to read "check these interfaces" or "this is from test ...
Forum Posts
If I place an obstacle in front of the Access Point, will the Signal Map show exactly what happens?In CMX I can only upload the building cross section, the Access Point moves into its right place, but I think the wave signal does not show properly if...
Hi Everyone, Do you know, if the virtual CSR 1000v router supports Local span configuration? - I have configured local span, as I would on any switching platform - Traffic is flowing in and out of the router via interface Gi1 - I want interface Gi2...
Hello,I did a home connection using a wireless router and client.I have a wireless router, 2 desktop computers, a laptop with a wireless interface card, a television, a cable modem and a cable splitter.I have done all the configurations. I connected...
Resolved! DHCP SNOOPING/DYNAMIC ARP INSPECTION
what is the difference between an IP DHCP snooping trust interface and a dynamic inspection trust interface. I'm asking in regards to where the switch interfaces where they should be configured points to.1) can we configure it on an interface pointin...
Hi,I was trying to configure Mac-address on 4948 L3 inteface. But there is no command to configure it.Can any body help whether it supports or not , if yes which image.I have following image:show moduleChassis Type : WS-C4948Power consumed by backpl...
I am using GNS3 in ubuntu 18.4 and right now i configure a tap interface and set iptables nat rules for the device inside the gns3 to connect to internet but say i have an infra like tap1->R1->R2->R3->R4->R5 with the below detailsR1 - f0/0 - 10.0.0.1...
Hello, I have a C3750 stack which is acting as my core switch for my internal network. I am in the process of replacing this stack for a new stack of C9200.As you can imagine, I need to be careful with this, as this stack is the heart of my network, ...
Resolved! DHCP between R1 & R2
Scenario Tap3->R1->R2my conf as below,R1enableconfigure terminalip dhcp pool pool1network 10.10.10.1 255.255.255.0default-router 172.16.1.0dns-server 8.8.8.8exitinterface f1/0ip address dhcpNAT in R1enableconfigure terminalinterface f0/0ip nat outsid...
We have mapped multiple URLs behind the Load Balancer with single public IP. From the nearest Cisco gateway router, we are passing netflow information to a peer. Is there a way I can pass the backend URL name ( or its private IP) to my netflow peer ...
Does anyone know whether issuing the "no service dhcp" will have any impact on the PCs getting their ip addressess from DHCP server x.x.x.x with default gateway having ip helper-address as x.x.x.x?The above command to be activated in the default Cisc...
I've been trying to set up Notepad++ for editing documents containing IOS-XR configs and I'm having trouble finding an XML file that will be helpful. The ones I've seen so far are pretty bare bones. I'm okay editing in some of my own keywords because...
How do I name the native VLAN in a Channel group?
Resolved! Accounting for Packet Drops, QoS
Hello,Does the total drops count from the policy map output data for an interface include only drops caused by QoS?What's prompting this question is the attached chart showing packet drops on the interface. The goal is to determine whether QoS is sol...
Hello everyone!I am trying to execute TCL WoL script using Python3 and "cli" library, that is running inside Guestshell on Catalyst 9300 IOS XE.In my running-config I have specified:'scripting tcl init flash:wol.tcl'so after executing "tclsh" I can r...
