what is the difference between WS-X4232-RJ-XX and WS-X4232-GB-RJ?
what is the difference between WS-X4232-RJ-XX and WS-X4232-GB-RJ?
Hi,My client is a remote office having a network of about 60 users. We have tested 10 workstations telneting an AS 400 on their head office and found only one (1) working.What could be the problem behind. Theres no firewall. Access list is not a que...
Hello,I'm trying to put Gigastack modules on a 3550-12G in an etherchannel.The documentation of the gigstack modules ( http://www.cisco.com/en/US/products/hw/modules/ps872/products_data_sheet09186a00800a1789.html ) suggests (i quote from the document...
When i tried to upgrade the existing code to c6msfc2-jsv-mz.122-14.ZA2.bin it went to boot mode. I had to backout to the old one again since it dint do any routing funcitons. Is there any bug in the code or is not compatible with Catalyst 6509 runnin...
(This is for my understanding)If you are a company that is 100% webhosting and uses multihoming with two ISP. How will DNS from the host resolve the correct path to your website?
The C3500XL do run IOS but are they vulnerable to the DOS attack outlined in the Cisco July 18 Security Advisory?If so I guees the only solution is to upgrade the IOS as they do not support ACL's as required for the work around.
I know that ISDN-BRI can dial-up (initiate a call/connection) to ISDN-PRI. My question is, thus ISDN-PRI can be configured to dial-up to ISDN-BRI?1 ISDN-PRI 30 channel module dialing to 15 ISDN-BRI? Any sample or links to sample configuration?
Hi,We have an VoIP network where an IP phone is connected to c2950 switch. I have configured the IP phone to trust dscp values, L3 Sig = 24 and L3 Voice = 46 (Bearing in mind using Cisco default values of VoIP COS=3, COS=5). The IP phone is not Cisco...
We're setting up an IDS on the lan and we currently use 2 4006 switches with a trunking fibre running between the two.We need some way to span all traffic on both switches to one switch port. It doesn't matter which switch it is as long as all traff...
Does 2950 series support layer 3 switching?
I am attempting to connect to 1751 routers w/serial interfaces via t1 line. Router "A" (host side) is identical to router "B" remote side. I want to keep them on the same subnet for simplicity purposes. I have performed this feat with csu/dsu modules...
I'm trying to migrate the E1 link from HDLC to frame-relay encapsulation. It works using back-to-back UTP (1,2,4,5) cable. One end i configure as switching and DCE type. Clock rate set when configure as back2back. When run in real E1 link, the ping p...
Has anyone tryout on Cisco WIC-1ADSL running on Singtel(Singapore) ADSL connection?
Hi,I 'm having CISCO 3660 router. Its currently running on 12.1(5)T10 version IOS . I need to upgrade it to 12.3. How should i go abou it?regards..
What command is needed to allow a catalyst 3548xl switch boot automatically. When the switch is turned off it stays at a ROMMON prompt. It will not function until I type the boot command but I do not know the command to make this happen automatical...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |