Other Network Architecture Subjects

Hello,does anybody know if Ciscoworks support CatOS 7.5(1)?I've just installed it on my Cat4006 and configured local user feature.But checking device attributes I'm receiving a result: Telnet: incorrect; Enable: Did not try; Local User: incorrect.I...

There is a command I used long time ago and I forgot.Basically this command will yield how much time the line has been used. It has something like this:line tty 1 (1000 sec)line tty 2 (2123 sec)So on and so forth. Please help. Thanks

Hi,1) i do a "show memory" on a cisco 26xx router. It shows me the Total Processor Memory and Total IO memory.When i add up these 2 values, why is it not be equal to total amount of DRAM in your router (as shown by sh ver)???2)Assuming the "sh memor...

I have several Paradyne frame savers (CSU/DSU)that according to pardyne can be managed by any"frame-relay router" according to the documentation I have to create a pvc dedicated for management. The text reads:The router to be used for management mu...

I have Cisco 1600 series routers at three locations tied back to another 1600 at the central site. I also have a Caymen router at the central site serving a a DSL connection to the Internet. I would like to pass the incoming internet traffic from the...

Hello,I appreciate if you can help me understand this "logging trap debug" in routers. I have setup a syslog server to collect messages from several devices including routers, switches and PIX firewall. All configurations at syslog server and network...

Im a student and i need help question will be posted ....A small medium enterprise co. has been utilizing cisco hubs model 2926 and boca hubs in a cascading hub configuration between the end users and the servers. Meaning the hubs are linked to each ...

Hi,We currently use Dial on Demand for some remote links. One particular site is configured to run at 64K but using load-threshold it goes up to 128K during peaks times.This site looks like increasing in size. Is it possible to configure more than on...

Sir,I have 2 questions about SFM module on C6k.1I got some error message on C6k:"*Jan 26 20:06:21: %ONLINE-SP-6-INITFAIL: Module 3: Failed to synchronize Port asic*Jan 26 20:06:21: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (env-related...

Hello,I am attempting to determine if the following is possible and if it is, can anyone help me out?I have two Cisco 2620 routers that are connected via a Frame Relay circuit. I route IP traffic through them as well as VoIP. On "Router1" I have a ...

I just see this link : http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t8/dtnbarad.htm#1079748and try to set router to control bandwidth from KaZaA. I used IOS version 12.2.13 on router 7200 and put these setting in c...

We have a 3640 router running IOS 12.2. I am trying to use NBAR and QOS to block or tone down Kazaa2 traffic. I have the kazaa2 pdlm loaded into my config correctly and it shows up in the list when I do a ' show ip nbar protocol-discovery'. When I t...

Can anyone recommend a stable native IOS with IPX support for a Cat 6000 running an MFSC 2 / Sup2?

Have multiple VLANs configured with ip helper address on all interfaces of the MSFC. Windows browser elections are passing over UDP 137/138 due to the helper address. When I use an acess group on the out interface of a VLAN to deny UDP 137/138, we no...

We have our seed device set to a 6509 which has 5 Cat4006 connected to it. ANI is only discovering one of those 4006 and I have compared their configs and seen nothing different. I did discover though that the 4 that aren't being discovered have 35...