When will the cat 4006 (IOS) be supported ? I have L3 links between my core devices and when a link goes down - DFM does not report it as down. I have enabled logging and snmp-events on the interfaces - please advise
I am at my wits end on this. Any suggestions would be greatly appreciated!(CD1 4th edition, on NT)Trying software distribution for the first time. I first got an error when I tried to initiate a software distribution job - the error indicated was:Pro...
Can "Small Network Management Solution" support PIX and Cisco Routers or it is strictly used for Cisco Switches.I already have CSPM in the network. Can it also manage the Cisco Switches or does it only support Cisco IDS blade for the managment purp...
I have a problem where I need to limit outbound calls from a central site 3640 to a branch ISDN network of 160 or so Cisco 800 routers, but still maintain inbound calls. The only applications that should initiate outbound connections are the apps th...
Hello, We have following resources 7206 router with AS5800 with the IOS c5800-k8p4-mz.122-7b.bin. and a 144 MICA modem card The problem goes here we get following console messages 09:20:29: %DS_MODEM-3-LOW_PARTICLES: Not enough particles - ...
Looking to use data compression on some wan links (t1/e1) where the links have IPSec configured on them.I'm not sure if you can compress encrypted data and even if you can the extra overhead on the routers may prove prohibitedAnyone had any experienc...
I'm using 2620xm with EtherSwitch NM integrated. Are the following command supported?* ip mgmt-vlan VLAN_ID* snmp trap-source VLAN_ID (Vlan_id different from management vlan)Is it necessary to set up a management vlan (Vlan 1) on the device?If i conn...
Hi,I have a Cisco RAS with 8 Analog modems NM.The users must use the system for dial-out, But have no knowhow regarding TCP ports ect.How do I dial -out using a group of the analog lines, so the used ports will be automaticaly selected?Is there a sp...
Would anyone be able to give me a config for a WIC-1AM . i would like to be able to use a 1720 to connect to my isp. any help would be much appreciated.
Hello,Would I have any problem if I use the same BGP AS number from different location that aren't directly connected to each other?We are tyring to set up a backup site, and there will no connections between the backup and main site. We were wonde...
TO all, I have an Engineer on site today, to perform an install and it is URGENT that I get the following working for extra resilience. Spent a lot of time prep yesterday for PPP callback from UK to Belgium, and now this task is the problem! Having t...
Hello all,I have installed CiscoWorks 2000 LMS2.1 (CD One 5th Edition and RME 3.4) on a Windows 2000 server platform.The Configuration Archive will not back up the configs of our Catalyst 2950-24, Catalyst 2950T-24 or Catalyst 3550-12T switches. The...
Hido we have any restriction to configure only someports with Jumbo Frame enabled ,leaving othersto default ethernet MTU on 16 ports GIG ?how does 6509 handle traffic between Jumbo/No Jumbo Ports ?are they any impact of switching performance in this ...
Hello,We're running CW2K LMS 2.1 and in Topology Services (version 3.2 Patch 0) our Aironet 340 and 350 bridges/access points are being discovered, but are showing up as Unknown and Unreachable. I've checked the SNMP and CDP settings and they are co...
Hello,i have the following problem. Between out central site and a branch there is a Frame Relay connection. Because of the high utilisation of this line i have to implement additional isdn lines. These isdn lines should be activated if the main line...
