we have meshed network, interconnected using serial lines only. Bandwidth of these serial lines varies from 64-K to 2-MBPS. We are considering Wireless link between major center for link redundancy, since the serial lines are not stable. The wir...
we have meshed network, interconnected using serial lines only. Bandwidth of these serial lines varies from 64-K to 2-MBPS. We are considering Wireless link between major center for link redundancy, since the serial lines are not stable. The wir...
We have experienced one hard failure of an NPE-400 in a 7206 chassis and another probable failure in another 7206 chassis. Both routers appeared to "lock up", i.e. no routing was going on, we were unable to connect to the router via telnet or consol...
We are installing about 270 2900 series switches. We made a cookie-cutter configuration for all the switches. The first 20 or so worked fine. As more were installed, we noticed the switches worked, but were not pingable.I went to one of the stores...
I have a 7206 on the network with a single FE on the I/O and a dual FE on slot 1which = the 600 BW points but there is also a GE module in slot 3 but shutdown which now brings the total to 1000 BW points. FE 0/0 is in use FE 1/0 is in use and I now w...
Hi,I would like know if is possible use a PA-POS-OC3SMI (155 Mbps) for collect the traffic from two E3 (34 Mbps). Of course, if is possible, I would like know how can I must configure the PA-POS-0CE3SMI for routing over two links at 34Mbps. I show an...
hi,my question:i have the task to implement voip over a 384 kb/s frame-relay link.for that i configured frame-relay fragmentation wit 480 Bytes.does cisco ios only fragment if there is a voice-call or is this fragmentation are active if there is only...
We have an Cisco Catalyst 4006 with the SUPIII engine. I would like to have all user ports default to an VLAN that only has access to a DHCP server. When the clients lease an address from the DHCP the port would change its VLAN membership to the main...
In RME 3.4 the Reachability Dashboard shows Last Response days from a few days ago. Also it shows 1 device down while this is not the case. It looks like the dashboard is not updated or not polling correct. Anyone seen this before?
Hi, if I configure a WS-C4006-S3 with the Config Tool, this 12112EW which enables IPX does not show up. But if the 4006-S4 is selected, than the SUP3also appears with the S4KL3-12112EW. My Question is: Does this Software supports also the SUP3 (WS-X4...
I'm planning on implementing three 2924 switches with 802.1Q. I was thinking of using Clustering to manage the switch. Is the Cluster Builder a chargeable software product?
Hi,I want to know if ospf can handle about 620 routes+ 630 routing table, reason being we have 620 remote sites all dialing to 2x3660 routers (hunt group). As the Mitel (remote isdn router) don't have ospf capability We had to define static routes...
Could CW2000 to capture traps from the monitored devices via SNMP and allert the personnel responsible with the network management (ex. an e-mail) ?Thanks
I've got two 64k pvc's that parallel each other running eigrp. When I telnet to the remote router from the local router, I get a trace that shows:Tracing the route to 208.234.171.23 1 10.203.131.110 64 msec 10.203.141.110 48 msec 10.203.131.11...
Hello,I have 2 main questions.1. I am connected to 2 ISP's, to both of them I am advertising one of my /24 network. When I use BGP looking glasses, they only show the shortest paths, only the paths to the nearest ISP for them, there is no path for th...
We currently have dodgy old WSC1912/24-a and WS2828 switches.These devices do not support command line.When imported into inventory, staus is telling me there is no telnet support, is there any workaround for these devices, or have I got to live wit...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |