I keep getting this error message. Why? :Uploading image disk0:c7200-is-mz.122-6f.bin from Prod-Inet2 (#2 of 2) Start time: 08 Aug 2002 12:28:11 EDT Error Info Code: 3001. Device Error: File Checksum calculation failed. Probable Cause: Device...
I keep getting this error message. Why? :Uploading image disk0:c7200-is-mz.122-6f.bin from Prod-Inet2 (#2 of 2) Start time: 08 Aug 2002 12:28:11 EDT Error Info Code: 3001. Device Error: File Checksum calculation failed. Probable Cause: Device...
How to re-initialize the RME 3.2 database ?thanks for help
I'm using IOS Version 12.2(4)B2. Thks.
Hi ! I have to set up Inter-Val routing between 1 Cisco 1721 and 1 3com 3300 with 1 port on 3 Vlan.I plan to use 802.1q standard. My question is: I have to purchase Ip plus for the Cisco 1721 or Ip base is enought ?Thank youHerman
How can I limit the amount of bandwidth going to an ether.port on a 3640??
Hi, I have a problem when dialing from a BRI interface to the PRI interface. I have tested it by pinging to 192.168.10.3 (this is the dialer interface of the PRI). Who can help me?by pinging to 192.168.10.3 It seems that a link is build up, but by vi...
I have a remote site linked to main building by a 100MB infra red laser. I trunk my Vlans over this with no trouble.Can I use an Aeronet 340 bridge as a backup link to pass VTP?
Are there any plans to port some of the Cisco management tools to Linux?(the ones that currently are made to run on Solaris)Thanks
When implementing traffic shaping on a 100mb ethernet interface, the traffic-shape command has the following associated paramatersrouter(config-if)#traffic-shape rate ? <8000-100000000> Target Bit Rate (bits per second)The upper limit seems to be 1...
Hi, I have a problem when dialing from a BRI interface to the PRI interface. I have tested it by pinging to 192.168.10.3 (this is the dialer interface of the PRI). Who can help me? by pinging to 192.168.10.3 It seems that a link is build up, but by v...
about the Configuring a Relay Agent on Cisco What Protocols I need - are these Protocols all necessary for the DHCP Relay Agent and can i let out or jump Protocols ??? The list of Protocols which are rated: > * Trivial File Transfer Protocol (TFTP) (...
I did a debug isdn q931 and got the following message when attempting to connect from one cisco 2500 to another. What could be the cause? Jul 29 18:42:57.471: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x49 Jul 29 18:42:57.471: Bearer...
I recently purchased a Cisco 827 router running OS (tm) C820 Software (C820-Y6-M), Version 12.1(5)YB5 to go with a PPPoE DSL line. Every few days, the router will completely stop responding - the ADSL CD light, RXD light, Ethernet CD, Ethernet RXD an...
Hi,If I've a PRI interface with multiple Dialer interface with dialer load threshold command, to permit to two call to a remote router with one bri interface I must type the ppp multilink command on the serial0/0:15 interface of the E1 controller lik...
I am about to upgrade one of my sites from 56k to 128k frame-relay. The site has a 1600 router and our corporate office has a 2500. My question is what changes, if any, will I need to make to the 1600? Below is the config as it is now for the 1600...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |