Can any one tell me the best Cisco Bandwidth Manager, through which i manager bandwidth of Particular IP, or even i want to restric bandwidth across particular MAC Address.Thank You
Can any one tell me the best Cisco Bandwidth Manager, through which i manager bandwidth of Particular IP, or even i want to restric bandwidth across particular MAC Address.Thank You
Hi All!can i do Ether chanel between 2 distribution switch(distance between the 2 Dist it 600M) via the 2 fiberPort(GBIC)what can i use in this Situation; single or MultiMode.ALSO CAN I KNOW THE WHICH SERIES of 2950 Can suppot the GBIC10xs
Hi All,Does Cisco 7606 GigabitEthernet modules support stacked VLAN (two VLAN tags)?If yes, how do I configure it?Thanks in advance.Regards,Sarah
Hi allwondering what software image i should use so i can run multicast over the network have a 6506 has been upgraded to 12.2(18)SXE5 and am wondering what i should use on my 3750G-24T-S3750G-24TS-S3750G-12S-Sam thinking of going EMI would any one ...
How to load balance (if can) or failover two Fiber channel like as below?interface GigabitEthernet0/1 switchport mode trunk channel-group 1 mode active channel-protocol lacp! interface GigabitEthernet0/2 switchport mode trunk channel-group 1 ...
Hi,Would appreciate if anyone can advise if catalyst 2924M and catalyst 5500 supports bpdu guard? If yes, what is the IOS/CatOs version to be upgraded to?Thanks.Christina
when i configure WFQ on an interface, i see a parameter called available bandwidth on the sh interface command which is less than the actual interface bandwidth. And if the traffic exceeds the available bandwidth then will result in output queue drop...
Hi,I'm trying to upgrade a SSL Service Module in one of our 6500.Following the guide at http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_guide_chapter09186a00805e34ed.htmlAfter booting on the maintenance partition and tryi...
Guys,I have 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX card, and I thought it using 1p3q8t techniques, but for some reason when i try to add this configuration to any interface on the cardwrr-queue bandwidth 5 25 70wrr-queue queue-limi...
Dear all,I am preparing my ccna exam and was reading this evening through the EIGRP protocol. At a point the autor writes that if you have a discontiguous network, you have to use the "no auto-summarize" command to make it possible that the routing u...
halloin a broadcast multiaccess segment with more routers running OSPF if both DR and BDR fail, does the DR and BDR election process restart or not ?francesco
There is a description in the following about Performance. How many is the size of the packet?> · 15 Mpps without SFM> · 30 Mpps with SFM and no distributed forwarding cards (DFCs) > · Up to 210 Mpps with SFM and DFCsSUPERVISOR ENGINE 32 ARCHITECTURE...
Hi,From http://www.cisco.com/en/US/customer/tech/tk389/tk621/technologies_configuration_example09186a008009467c.shtml, it says, "do not use portfast when you have switch-to-switch connection. In this case, the command can result in a loop."For e.g. w...
Hi,How do I log the messages on a switch to a syslog server at syslog level 3 but on the switch itself I would log at syslog level informational?Could anyone advise how should I go about doing this?Thanks.
Is it possible to define passive interface for all interfaces on 4510R switch except the ones connected to routers, so that I don´t have RIP protocol passing through the LAN?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |