how do I clear a route that eigrp has generated ?
how do I clear a route that eigrp has generated ?
Does anyone know where the 1000Base-ZX specification comes from. I can find the -SX and -LX definitions in the IEEE 802.3 standard, but I can not find any references to the origin of 1000Base-ZX or 1000BASE-LH.
G'Day AllBe brief. Have a situation for an important WAN site, that has its primary and secondary links to clud delieverd over ethernet. Ethernet service was going to be plugged directly into the 4506's SUPIV (dual 4506's) each, and run RIP-V2. Howev...
Hi!What do i need to do to join the exisiting vtp domain? Will the switch join the domain by itself without any configuration when i do a trunking to the existing switches?(there's no password set for the vtp domain).What need to be noted before join...
can anyone tell me what this is and how to set it up ?
I am designing an upgrade to our current network that will contain a 6500 switch and i wanted to setup vlans with the switch. I know that this switch has the ability to perform routing on its own so i do not need an external router to route between t...
If I wanted to advertise a network of 19.45.74.0 would I put this into eigrp, could I put network 10.0.0.0, would this also work ?
I have a cisco 2651xm router that I have been configuring. I am just trying to get used to cisco commands and learn, so I will config it, then do an "erase start" and reconfig it. Everytime I do an "erase start" and reload the router it comes up wi...
Hi what will happen if two switch with same MAC-ADDRESS and same STP priority will run STP , how will elect to the root bridge ???? how the STP process will handle this situation?thanx
I have a (2) 4507s, (5) 3000 series switches with fiber gbics. Each 4507 has a 6 port fiber blade. the (2) 4507s will etherchannel together using (2) of the (6) fiber blade ports. (4) out of the (5) 3000 series switches will have room to connect to...
Im seeing a lot of unusual ST topology changes, coming from a port which is supposed to be in blocking state: Cat4006 Gi1/2 (see thumbsketch)+------------------ PortChannel ------------------+Cat6513A --- (Gi1/1) Cat4006 (Gi1/2) --- Cat6513Sforw --...
WS-C3750G-24TS running12.2(20)SE4, RELEASE SOFTWARE (fc1).sho mac-address-table aging-time Vlan Aging Time---- ---------- 253 300 252 300 254 300 255 300 1 300 251 300--------The aging is not working. I can failover so...
Hello.I'm gonna deploy qos policy including priority queue on cat6500 for Voip , Vide, and Multicat.The module's capability(WS-6408A-GBIC)is 1p2q2t.So i'll assign Priory queue for Voip and Video. I already had make configuration as below.Please check...
I am trying to figure out what is going on. 2 Times now the switch has been restarted. Both times in the early AM (2-3am) Is there anyway I can determine the cause? its not a UPS issue as other devices on the same UPS have been up for 8 weeks or ...
Can I use 8 SFP of the principal and redundant Supervisor V-10GE of simultaneous form?Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |