Routers - Small Business

Hello,I'm trying to configure the LACP for W2k8 and I have strange thing :My network is :1 SRW2008 witha Synology NAS connected with LACPmy PC running under W2k8 with LACP1 another PC with single1 Router running with DD-WRT fw , used for DHCP , WIFI ...

Hello everyone,Currently I have the Small Business Router SRP-527.  It is being used to connect my small business network to the Internet with 2 VLANs. (the first is the internal network that connects to the Internet and the second is for my client's...

Got Problem when try to connect from an fresh installed windows 7 x64 PC with internet Explorer 8.The Error Message:               Cisco-SSLVPN-Tunnel Install Failed: Error in Removing existing Cisco-SSLVPN-Tunnel Adapter!Internet Explorer is startet...

Greetings! First off, I am NOT very network savy so please bear with me..My wife wanted to be able to VPN to her office from other computers.  I purchased the RV120W as it appeared that the QuickVPN would be sufficient for my wifes purposes.  I insta...

1) the log entries are out of order and incomplete in the router compared to the syslog file on an external serverFri Jul 22 07:32:53 2011(GMT+0100) [618111043][Kernel][KERNEL] printk: 2 messages suppressed.Fri Jul 22 07:32:53 2011(GMT+0100) [6181110...

Hello,I was trying to connect 2 RVS4000 devices to each other creating a vpn tunnel but the status of the link is always "down". I have followed the instructions on the "Administration Guide" to connect a gateway to gateway vpn tunnel using static ip...

What is the magic formula to get OSX clients to connect to a RV082 with IPSec?  I have tried IPsecuritas, but am unable to connect.  From the logs it appears that phase one fails as they can't agree on settings.Attached is the full log.

Hello,a have 1 rv082 in my head office, and 1 rv042 in each branches. They work in permanent vpn tunnelsSo how i can configure it to bring WAN2 VPN in the same network when my WAN1 fails?

Hey,I'm having a problem forwarding port 1723.  What i'm trying to do is to use VPN to access my server pc and I don't want to use the VPN software that is in the router.  When I telnet the port it goes through but when i try to access it outside of ...

Hi All,Trying to configure an SRP527 to work in conjunction with a 3560G switch....My local subnet on the 3560 is 172.23.x.xThe subnet on SRP527 is 192.168.x.xEverything can ping each other, except I just cannot get any internet access from 172.x thr...

Hi Guys!My company has just purchased an SRP 527w and an RV 042.I'm a noob when it comes to routers and vpns and all that,so my question isthat how would you go about configuring the two,so the 527w is the router and the RV042 would be our VPN server...

How to configure ISDN and framerelay in cisco 2503 and 2803 rotuer by CLI mode

Hello all,This is my first message. I have downloaded and read the RV016 datasheet.I would like to know if RV016 is a good choice for my use :4 WAN connections from ADSL2 routers.1 LAN connected to a Switch1 server on DMZaround 20 PCs on the SwitchI ...

I have installed a WRVS4400N router for a client and created 3 vlans.  I would like to route some traffic between the vlans so I turned on intra-vlan routing.  Is there  a way to limit what traffic is routed between the vlans?  I only want computers ...

I have an ADSL connection and have configured the PPPoE subinterface on WAN1 (ADSL)  this connection has a static IP, and I know that the ISP gives that to me through DHCP however I have 4 or 5 additional IP addresses also provided to me on that same...