This topic is a chance to discuss more about Enhanced Interior Gateway Routing Protocol (EIGRP) fundamentals. The session seeks to clarify the status and fundamentals of the EIGRP protocol. In addition, the experts will discuss the common steps used ...
Hello Experts I am looking for a solution to carry the EIGRP metric over the services provider MPLS network, this is not owned by us MPLS network so I cannot tune the bgp community to carry metric from EIGRP... so I planned to use EIGRP OTP , wit...
Hi Guys,I have always read that OSPF has two types of LSack . ( Implicit ack and explicit ack ). I would like to know the difference in detail.Please state the examples where implicit and explicit ack are used and in which scenarios are they sent .R...
Spotted this in my CCIE lab and am rather baffled. Why would EIGRP redistribute a static route even though I've configured it not to?Configuration:ip classess!router eigrp 65100 network 198.19.0.0 0.0.1.255 no auto-summary!ip route 198.19.0.0 255.25...
Hi!I just experienced issues with a C881G-4G-GA-K9 (no IP-Address on the interface, no service...).In the output of show cellular 0 all, in the Data Connection Information I got following:Data Connection Information===========================Profile...
Hi, So I have hundreds of sites configured the same as this site with the weird issue. It's not the DMVPN configs. Issue is, I have two DMVPN tunnels configured to two different hubs on the router. When both DMVPNs are no shut, they will stay up ...
I have a ISR 4451 router on code Cisco IOS XE Software, Version 03.10.06.S - Extended Support Release Whats the lastest code I got to ? Thanks in advance Thanks JT
Hi, I would like to know how to add multiple adress to a loopback in cisco ? I have to configure a loopback that has 31 hosts but I can only set one, do you have any tips ? Thanks
Hello there, I will be upgrading 7200 Series Router model to 4500 ISRs since the former one is already past End of Life. I have configured 4500s with the configuration what is present in 7200s and have sent the device to the remote location where it...
Hi, I am creating a network within packet tracer, but am having trouble understanding how I can make my OSPF network take the most optimum route.I have manually costed the Gigabit interfaces at 2, and serial interfaces at 100 using the ip ospf cost c...
Hello reference paper: https://www.cisco.com/c/dam/en/us/products/collateral/routers/3800-series-integrated-services-routers-isr/prod_white_paper0900aecd806f698a.pdf In my case I need to connect C2811/C2921 in Cross-Stack EtherChannel to a stack o...
We have couple l2tpv3 tunnels between C2911 and C1921.which, in turn, pass through a DMVPN tunnel through the provider cloud.And plain copy operation of a data, say ~100Mb and more in vlan 5 that xconnected lead to a high cpu load up to 100% on a C2...
Hello all,Please reference the image for convenience. R1 and R2 are our routers running ebgp with two isp R3 and R4 which are sending default routes towards us.R1 and R2 are ibgp peers also sending default route to each other also running vrrp.R5 is...
Hi there, Thanks for reading. I'm wondering what the upper limits as far as bandwidth for tunnel traffic on 800 series routers. Will they support a 50Mbps circuit connection? Thanks again, Bob
The L3 tunnel is up and works great. Now I'm testing it with my local ISP services and I'm trying to manage the remote ASA through the tunnel. I can ping/ssh from PC to PC through the tunnel (192.168.168.140 <-> 192.168.180.4) but I can't ping/ssh ...
