A Cisco router wan interface had a config change to support a new 1G internet circuit but had to be rolled back to the original 100M circuit. The speed was hard coded back to 100M but duplex left blank. This appears to have caused the duplex setting ...
Forum Posts
Hello everyone,I wanted to share a lab I started working on.As you can see above I have one Core Switch, with two Distribution Switches and 3 Access Switches. The steps I've taken at this point are below:1. Entered the CLI of DSW2(Top right switch) a...
Resolved! bgp default gateway ways
Hello everyone i want to configure BGP to send the default route to a neighbor, i receive from ISP full veiw i can't advertise to another peer 0.0.0.0/0.In lab on EVE, everything works perfectly by the way this step i done for 0.0.0.0/0ip route 0.0.0...
Hello, I have two ISR1000 routers with the security license activated. securityk9 (ISR_1100_4P_Security): Description: securityk9 Count: 1 Version: 1.0 Status: IN USE Export status: NOT RESTRICTED Feature Name: securityk9 Feature Description: ...
Hello Team, I wanna upgrade our edge routers to the latest Gold standard, we're currently running Bengaluru 17.6.5on our C8300-1N1S-6T Cisco Routers, the latest Gold standard is Dublin 17.12.5a. Thats a significant jump,is there a tool that Cisco pro...
Hello,I have a prefix that I learn from another AS1, which I set a "no-export" community inbound to AS2. AS2 has eBGP sessions to AS3 and AS4. I need to remove/override the "no-export" outbound to AS4 only. I tried the below policy but the prefix is ...
Hey,Just purchased 2 x 3650 switches. I need to set things up to replicate my config from the old 3750s. I've got the switched powered on, ethernet plugged into the back MGMT port and other end into my laptop. I've disabled wifi too. Ethernet shows u...
Hi everyone, Regarding the backup power for the C8200-1N-4T Whether the PWR-CC1-150WAC can be used as a backup for the built-in power supply on the C8200-1N-4T device, or if it is only intended to support the PoE module? Thanks
Rom image verified correctlySystem Bootstrap, Version 16.9(1r), RELEASE SOFTWARECopyright (c) 1994-2018 by cisco Systems, Inc.Current image running: Boot ROM0Last reset cause: PowerOnC1111-4P platform with 4194304 Kbytes of main memory........no vali...
The system consists of a switch with two VLANs for hosts, and a router with two WAN connections.Switch:Interface vlan10 - 192.168.1.1/24, with some hostsInterface vlan20 - 192.168.2.1/24, with some hostsinterface g0/12 - 172.16.0.2/252, uplink to rou...
Hi everyone,I’d like to set up an mDNS gateway on my Cisco C9300-A, filtering by instance name.Suppose I have three different networks, X, Y, and Z, where VLAN X is a service VLAN.I’d like VLANs Y and Z to be able to see only certain services availab...
Hi AllCan anyone tell me the user cases for Ethernet over GRE, what do people use it for normally? would it to be to extend vlans etc? if so why would you use this over L2TP etc?Also, what would the basic configuration of this look like ?Cheers
This is how my tipo will look end of the day.eBGP peer Edge <---> ISPeBGP peer between Edge < --- > Border-Leaf (I am using 65355 to peer eBGP with Edge)Inside EVPN/VXLAN fabric I have BGP 65001.I am Planning to do following config for stumble guys m...
Hi Guys I am looking at purchasing some 8200 / 8200 routers in non SD WAN mode, I have a query on the licencing.I need the DMVPN functionality, this appears to come with the DNA essentials licence with comes with a "perpetual" network stack. If I pur...
Hi, starting something new here and seem to be having an issue. My FPR1010 is set in PPPoE Mode and obtains a Static WAN IP as its GW and I also have a block of 8 Static WAN IP’s (6 usable). I was trying to assign a DDWRT router to an Interface on th...
