What is the recommended setup for the following situation where there is redundant border routers connecting to the ISP with full tables? Needs to advertise a single /24 in a redundant configuration.
Forum Posts
what is the benefits using vrf in LAN instead of svi interfaces? I see it was deployed this way in client LAN, reminds me mpls config with all route target and rd on the lan switches. I still can't get the reason why vrf but not vlan routing.... an...
Hi all, I'm trying to learn route redistribution. Below I have attached the topology where the network consists of EIGRP and OSPF. I understand that route redistribution is used where we are running multiple routing protocols and we need to transla...
Hello, we are experiencing intermittent cuts in the reception of multicast traffic. There is a multicast sender that sends a multicast packet to 239.1.2.3 each second, but after a variable amount of time in the order of 2-5 minutes, the multicast rec...
I am trying to get my eigrp routing to work while using non-default vrf's Within the default vrf the configuration was pretty similar to IOS but when I try to configure it to run in my secure VRF I cannot seem to get it to work. Any idea's will help....
Hi, we have some overlapping networks in our WAN. I need to route the traffic from 192.168.128.0 to one IP (10.3.4.7/32) through a VPN . The problem is the router has got an interface with this network 10.3.0.0/16 and the administrative distance of d...
The obvious fix is for R1 and R2 to have a static route to the gi1/0 IP address of their neighbor. One possibility of allowing router 1 and 2 to both be used for internet would be to set the weight on each router. route-map Set-BGP-Attribute...
Resolved! WLC 2504 Keeps Dropping all AP'S
I'm having a Cisco 2500 Series Wireless Controller and it keep dropping all the AP's, what could be the problem and i have attached pic of wlc. Any assistance would be really appreciated.
Resolved! OSPF Vlan
Hi All, if you please i have question if i am configuring ospf on Nexus 7K and i distribute the static and connected on that core, should i add router ospf 1 area 1 in each vlan and interface or no ? (config)# interface loopback (config-if)# ip ad...
Good morning, We're looking at purchasing a 7604 or 7606 chassis and using S2T-10g-XL route processor and ws-x6908-10G-2TXL line card but I'm getting conflicting information online about whether the RP and line card are supported in the 7604 or 7606 ...
Is it possible to filter outgoing VRRPv3 announcements on the VRRPv3 interface? I have the following interface on my CSR1000 router: interface GigabitEthernet1 service instance 10 ethernet encapsulation dot1q 10 rewrite ingress tag pop 1 symmet...
Resolved! Multihoming BGP and static route
Hi friends,I'm using 2 ISPs (ISP-A and ISP-B), have my own block of public IP addresses (170.X.X.0/22) and my ASN (26XX25). I'm using a Cisco ASR1001-X Router. Besides, I have a BGP session established with ISP-B and ISP-A is using default route (in ...
Hi, I have the following network with RIP (v1) static routing. I have advertised the networks and pinging works for each end device. Now if I disconnect the connection between R2 and R3, should the PC 172.168.20.10 still be able to ping PC 172.168....
I have a network with a central site plus about 30 remote sites (hub and spoke, EIGRP). A couple of the sites currently have no users or devices generating traffic, but are getting swamped with traffic transitioning to other sites. I'm at a loss to e...
Resolved! EIGRP to OSPF
Hi I have EIGRP running between 2 routers and a core switch in my setup the 2 routers are directly connected to the core switch. This setup is due to change with the introduction of a fortigate firewall between routers and the core switch. The ...
