Good morning, I'm trying to configure an ASA cisco in my network. I have a Juniper SRX100 router, configured as a bridge, then, directly connected I have the Cisco ASA and connected to the inside interface my switch Catalyst. Connected to the ...
Forum Posts
Resolved! What is the use of GRE tunnel? (Newbie)
Based from what I have searched, GRE is used to create a virtual link between routers and allow them to be directly connected, even if they physically aren’t. "Suppose R1 and R2 are routers at two far ends of our company. They are connected to two c...
Hello,I have formatted the flash and rebooted the router C891F . The PASSWORD RECOVERY FUNCTIONALITY IS DISABLED, so that I cannot press the reset button. I have copied the valid on the usb and conneted it to the router but it was not working. i re...
Resolved! problem with VDSL on 887
I already have a 887 working with VDSL on a second location. I configured another 887 with the same config (changing logins, passwords and IP ranges) and while the connection seems to come up (ppp led goes on), the CD led starts blinking again after...
Hi every experts, I would like to make the enquiry on how to set QoS on a specific interface based on http/https/udp on switch. We have some VIPs who are seating at WTC and they found running Reuters program slowly via our corporate network (Howeve...
Resolved! Cisco 2960 + High cpu skipes
Hi Guys, We are facing intermittent high cpu spikes on Cisco 2960 (2960-48TT-L), We are unable to find out exact processes which are causing high cpu.. We wanted to configure EEM script to get the exact logs during high cpu. Can we configure it...
Sir, I have switch Cisco WS-C3550-24 connected with cisco WS-C4507R. These 2 having same subnet 10.19.250.0/24. In 4507 the switchport Gi5/30 in vlan 1 10.19.250.8/24 is having connectivity with 3550 switchport Fa0/4 in vlan 3 10.19.250.11/24. I a...
Hello, I have a little problem with OSPF and default gw. My 2 routeur R1/R2 receive the fullview (BGP) without default route. I generate a default-route in the OSPF with R1 and R2 QFX1 and QFX2 receive the default route (0.0.0.0/0) I want to QF...
Let's say we have 2 sites(main and Dr) in 2 different cities that have 1 circuit each from the same ISP. Lets say we get a default route for both, and lets say we also advertise the same /24 through both. currently the primary circuit is the main s...
Hi, I have a Cisco RV320 router I want to set it up to use a PPTP connection I am having 4 problems setting it up: (I am not a professional in networking just a simple home user...) They said I should have the router obtain the IP address automatical...
Hi all, I seem to be experiencing an issue whereby the subinterface on my router will continually drop when there is no traffic being passed on its associated VLAN. I have done a source ping to bring it back up which was successful, however i would l...
I have an IPsec LAN-to-LAN tunnel between a Cisco router and a Palo Alto FW. The tunnel remains UP-ACTIVE if there is interesting traffic - The tunnels goes down if there is no interesting traffic. The problem I am having is that I cannot bring the t...
Hi Everybody, I'm doing some exercise about MPLS VPN and in particular Accessing Internet from a VRF. As i understand there are 3 standard methods to accomplish that: 1) Using Global Routing Table with another physical interface or subinterface; 2) U...
Hello, everyone! I met the question about how to make the Guest OS use 4G to connect with Internet on IR809. The Cisco IOS can use 4G to connect internet but GOS can't. Is there any configuration needed to make? I checked so many config guides but ...
I want to know that what is the cable for Cisco ASR920 USB Concole ???USB Male to Male???
