Hi Fellow users, we are deploying an ACI solution and the use case is to have NFVs (network function virtualization) like CSRv and ASAv running on the CSP2100s. We will be connecting to the CSP 2100 using VPC from the leaf switches. I am a bit confu...
Forum Posts
Dear friends I need help With my cisco router. I have CISCO2921-SEC/K9 with EHWIC-4ESG. What I want I access to web server from my internal network and from whole internet. My public IP on WAN port is 212.87.232.8. My internal network which is ...
I have a 3560 Switch, a 2901 Router, and an ASA 5520 on the switch Gi0/1 to the router Trunk with vlan 10,12,14 That is working I also have the guest as ASA 0/2.16 confnected to port 0/4 on the switch. 10,12,and 14 get the dhcp from the rout...
Hi All We currently have an MPLS service with around 20 branches hanging of it. They are all running BGP with the ISP. I am now overlaying this with IWAN and using APIC to set it all up. The issue I have had is that the APIC has deployed a config to ...
Hello There Can cisco ISR4351 support Two SM-X-4X1G-1X10G (10G)? how many DRAM and License is needed? TNX
Resolved! GLC-FE-100EX compatibility with ISR4451
Hi, following link says GLC-FE-100EX is not compatible with ISR4451 whereas it is accessible under ISR4451 in CCW, Please advise https://www.cisco.com/c/en/us/td/docs/interfaces_modules/transceiver_modules/compatibility/matrix/100MB_Tx_Matrix.h...
Resolved! No internet access from VLANs
Hi, I'm very new for CISCO switches. Recently my company install 3650 gigabit switch and I connect it to our Internet line which has static address. And I add 2 VLANs, one for Servers, two for Office PCs. Now, inter-VLAN routing is no problem but all...
Good evening! I'm working on mutual redistribution on a pair of 7Ks OSPF<->EIGRP. The situation is my OSPF and EIGRP domains were originally built with no real design. Previous admins would just pick random ranges, so summarization is difficult to...
Hi guys, I have setup 2 PE's directly connected and created gre tunnel over this point 2 point with mpls ip command . Configured loopbacks on both routers for bgp peering. Tunnel and loopbacks advertised in ospf for reachability . Bgp and ldp pe...
Please some one can confirm with solid evidence as i.e data sheet or example in tested environment. I want to run mpls over gre on below platform with specs below, i have tried everything but did not work. So thats why i need to confirm platform sup...
Hello I am using reverse telnet through the AUX port, with the input protocol as ssh line aux 0 modem InOut rotary 1 no exec transport input ssh transport output all speed 115200 ip ssh port 2000 rotary 1 SSH'ing to port 2000 makes use...
Resolved! Do ISR 4000 series support OC3/OC12
Please tell me if ISR 4000 support OC3/12 circuits. I haven't been able to find any information on cisco regarding OC3/OC12 support by ISR 4000. If ISR 4000 series routers don't support OC3/12 then please advise which other ISR series routers without...
Hi team, I am wondering if I can stack 550x switches not through SFP Fiber...Would like to use the 2 - 10G connections for other stuff. Can I use the simple Coper as described by cisco for stacking? Can't find allot of installation guides for these...
Resolved! SG550x Switches
Hello, I was wondering, since I couldn't find anything practical online, I have ordered 2 550x brand new. I want to stack them and connect with Port-Channel to an ASA, one interface to Switch1 and the other to Switch2. Once Stacked, I supposed Port...
Hi, I have two mellanox switches connected to Cisco L3 switch stack using two 10gig interfaces. On cisco two ten gig links are configured as port-channel trunk at L2 and on Mellanox 10gig interface from each switch is connected to Cisco is set on ML...
