Hello, can anyone help me to reach the follow scenario? - I have two different carrier that send to my router a full BGP table - initially I use local preference to chose one carrier (let call it C1) as best -if bandwidth of link with C1 reach 75 %, ...
Forum Posts
Hello, Im new to the ASR920 service instance but would like to know if anyone has done traffic policing on a service interface. Scenario is multiple service instances servicing multiple downstream clients configured on a physical interface. I would l...
For the Cisco 891, the description for the PPP LED says a Green LED status means: "At least one PPP session is established.” Point to Point is supposed to be a protocol that connects on a serial port, as it is defined. On the Cisco 891, the v.92 ...
From the above Topology (Sorry for size), I've gotten everything except the NBMA to form an adjacency, and I had kind of some derp moments like forgetting to no shut interfaces - However I think I finally got all the configs correct but it JUST WON'T...
Hi,Can any one clarify my doubt , this is regarding EIGRP route advertisements.Generally EIGRP uses multicast address to advertise subnets to its neighbors. If we have 1 Head office router connected to 4 branch office routers.And if we don't want to ...
Resolved! Reset an Interface is in down state
I am trying to figure out a script or SLA configuration which applies the Shut/No Shut command if an interface goes down on a cisco switch, 3750 Can anyone guide me on this issue ? Below is what I have for the SLA Config, however, the interface ...
In our environment we have a mix of Cisco and non Cisco appliances. Those non Cisco appliances do not support EIGRP. So now we have an environment that is a mix of EIGRP and a lot of Static Routes. We are looking to convert to OSPF so we can run one ...
Hello please help me about Cisco AIR-LAP1252AG-A-K9 reset and reconfigure from network
Hello, I am trying to configure DMVPN connection between two routers (and more programmed), following this diagram: or the routers, i'm using: C7200 with IOS: c7200-advipservicesk9-mz.152-4.S5 The configurations used are attached. My question now, w...
Dear All, Can anyone tell me that either is there any cisco nexus 5000 series which supports layer 3 routing (ip routing, static routing and routing protocols) also supports qos dscp on interface? please mention the model number for these features in...
Hi , I am unable to learn EIGRP routes from DMVPN neigbour . Also getting alert *May 23 01:50:32.219: %DUAL-5-NBRCHANGE: EIGRP-IPv4 222: Neighbor 10.248.2.2 (Tunnel400) is down: retry limit exceeded*May 23 01:50:32.960: %DUAL-5-NBRCHANGE: EIGRP-IPv4...
Customer has come to me with an interesting routing / load balancing question. Scenario: Large MPLS cloud to 50+ remote Branch locations with two Data Centers, A and B. The PE routers in the cloud at each branch has connections to bothe Data Centers....
all: i configured a new ASR1002 router yesterday,i powerd on the ASR1002 to check the device include some SPA moduler,but i found my console screen display like this""Warning: filesystem is not clean"and "%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp...
we have a block of IP's which belong to ARIN and used in UK - we seem to have geolocation issues - BT (ISP) not helping us - whom do we report this to? reported to ARIN and RIPE but no joy Though it shows the correct Public IP on geolocation websit...
I am doing the power audit for 7600 and 6500 series routers currently running inour network.Cisco Power Calculator recommends different types of power supplies. Some are mentioned as Combined e.g Combined WS-CAC-6000W and some are tagged as Single/Re...
