Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

For some reason I can not get the config correct on my 1811. I have been banging my head against this for a week now. I have a dhcp server at the ip listed as the helper address but for some reason I cant get a dhcp address on FE1 and cant get dhcp a...

I am looking at moving to a 10GB backbone for a small campus of about 70 switches that go in to a single modular 4510. I was looking at the Catalyst Catalyst 4500X-24-ES model and using two in the core of the network. There are three additional build...

keebs1077 by Level 1
  • 348 Views
  • 3 replies
  • 0 Helpful votes

Hi, I am trying to establish IPSec tunnel between HO and multiple remote sites. I have configured Static tunnel on remote branches and dynamic tunnel on Head Office. The problem is IPSec tunnel is not comming up when I am using BGP as a routing proto...

Hi team! Once again about GRE tunnel speed: We have to ASRs and GRE tunnel between them (West and East sides). In general, we using this tunnel for our applications and services. But i think it's very bad idea using GRE tunnel for this kind of applic...

Hi All, I'm looking for a bit of product/configuration advice if possible. We have a single 1Gbps internet connection that is coming into a building that we want to terminate and provide to a maxium of 10 tenants. The tenants will be providing their ...

de1denta by Level 3
  • 378 Views
  • 1 replies
  • 0 Helpful votes

Hi all,I have HQ and mutiple branches in Hub-Spoke environtment. All site comes with 2 link. Primary link is MPLS using BGP, backup with DMVPN over OSPF.if let say one of the branch MPLS connection having problem(intermittent, high packet loss), I wo...

Hi guys, I have just upgraded the IOS software for a cisco 6509 E... I did it using flash cards, the upgrade took long and I wasn't able to remote login to the device, I physically check the device and see all the led lights are up.... I can console ...

s k by Level 1
  • 169 Views
  • 2 replies
  • 0 Helpful votes

Hi Guys, I just start experiencing this weird behavior on my Cisco 2811 Router. Recently I added to my home learning lab Cisco 2811 with integrated Cisco EtherSwitch Service Module (nme-16es-1g-p). Router has just basic configuration to join my home...

CyborgX_CZ by Level 1
  • 23815 Views
  • 9 replies
  • 0 Helpful votes

Hi allWhen I configure bgp ,i am getting errorThe below is the configuration. ??interface GigabitEthernet0/0 ip address dhcp duplex half speed auto!interface GigabitEthernet0/1 ip address 10.1.0.2 255.255.255.252 duplex auto speed auto!router bgp 646...

Guys, need your help understanding  1. I noticed 2 same IOS image files in the bootflash: for a 6509E sup2t, below is the output! XXXXX>sh bootdisk: -#- --length-- -----date/time------ path1 33554432 Jan 12 2000 xx:xx:xx -05:00 sea_console.dat2 12028...

s k by Level 1
  • 252 Views
  • 3 replies
  • 0 Helpful votes

Hi there Bit of a newbie here - I've managed to acquire an unwanted 1841. I want to configure this as a router and firewall for a small server room. I have limited IOS knowledge but would like to build this from the ground up. The first question I ha...

I'm running IOS 03.03.03SE on a 3650-48PD switch.  I have an AT&T ASE circuit that connects to our other locations.  The port uses a 1000BaseSX SFP module and is configured as: interface GigabitEthernet2/1/1 no switchport ip address 10.254.1.XX 255....

sbrock by Level 1
  • 351 Views
  • 2 replies
  • 0 Helpful votes