Good evening,I recently encountered an issue with my project here. From a given computer on a router I cannot ping another computer on a different router. For example, I cannot ping a computer from the Berlin router with a computer from the DC rout...
i created L3VPN senario to test MPLS VRF traceroute functionalityCE-1 (R1) 1.1.1.1 CE-2 (R6) 6.6.6.6when i did traceroute from CE-1 to CE-2 , below output is getting , but my question is when R3(P) router receive the traceroute with ttl 1 s...
Hi anyone,Quick question, but am I right in assuming that the purpose of Split Horizon in EIGRP is to suppress unnecessary updates rather than to prevent routing loops?DUAL (and the FC) seems to take care of routing loops, so I'm thinking that is its...
Dear all, Currently we've obtained ASR1001X and the new redudancy configuration requires us to pass dot1q traffic through 2 interfaces. It seems we cannot familiarize ourself with trunking and vlan interface when it comes to pure L3 devices. A diagr...
Hi I tried to write these commands in CLI (using Putty) for cisco ISR1100-4G but it seems like the VLAN command is not recognized.Regards,Aria Step 1Ensure that the router is in the factory fresh mode. If the router is not in the factory fresh mode,...
Team,Currently we do not have an ACl on our outside interface. If apply the following ACL will it only block the deny ICMP statements?Extended IP access list DENY_ICMP10 deny icmp any any timestamp-request20 deny icmp any any timestamp-reply30 permit...
Goodmorning,Or afternoon/evening. I'm looking to trace a packet to and from an external source, like 8.8.8.8. Currently it looks lik i'm having an issue with traffic going out via a cabled interface, Gi0/0/1.100, which is good. But the return traffic...
Hello Team, I hope you are doing well!I'm trying to implement PBR on Industrial switch IE-3400. I used the how to below, but the result was not ok.https://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie3X00/software/17_3/b_ip_routing_17-3_iot_sw...
I am trying to nat the destination address with an ASR router.Source --- Source IP: 96.97.98.99 Destination IP: 12.34.56.78Router ----NAT the destination to 10.0.0.4After NAT Source IP is 96.97.98.99 Destination IP is: 10.0.0.4I don't seem to be abl...
How do I set up a Static default route for a particular vlan on a RV34x series router? I am trying to send all traffic from a particular subnet over the VPN. As of now only traffic destined for the VPN network will go over the VPN but I want ALL traf...
I attached my Packet Tracer file for review. It would only attach as a zip file. Can someone tell me why DHCP is not working on PC-A and PC-B? I receive the error: DHCP failed. APIPA is being used. I used the show ip dhcp pool command. I triple chec...
Hello alli am running into an issue where even though i'm able to successfully leak routes from a VRF to the global routing table and vice versa, devices inside the VRF (4.149.253.0/24) and devices from the global routing table (13.38.0.0/28) are sti...
Rtr1 ----Cost1-----> Rtr2 (Area13)Rtr1 ----Cost1-----> Rtr3 (Area13)Rtr2 ----Cost10----> Rtr3 (Area0)Rtr2 ----Cost10----> Rtr4 (Area0) If i redistribute static route on Rtr2 then Rtr3 learns best route from Rtr1If i redistribute static route on Rtr4 ...
Hi,We have mGRE DMVPN tunnle between one Hub and 7 Spokes. Other 6 Spokes are working fine but one Spoke is not connecting to Hub.Spoke shows DMVPN on IKE state (tunnle is not working) and Hub is not adding nhrp entry in table.Spoke DMVPN TunnelPleas...
Hi; one of my routers in my lab (ISR 4331 - IOS-XE SD-WAN image 16.10.1) crashed so it keeps rebooting after showing the some error messages, one of which is: cisco isr 4331 %PMAN-0-PROCFAILCRIT: R0/0: pvp: A critical process viptela_start_sh has fai...
