Hello All, I have what I hope is an easy question. Device: ASA5512 IOS: 9.5(2) Goal: I would like to set up my ASA to use interface names that are not "outside" and "inside". Information: I know how to change the names of the interfaces, add NAT ...
Hello All, I have what I hope is an easy question. Device: ASA5512 IOS: 9.5(2) Goal: I would like to set up my ASA to use interface names that are not "outside" and "inside". Information: I know how to change the names of the interfaces, add NAT ...
can I insert HWIC-2FE when it is online? thanks,
I want to understand what is the use of NAT-T ? i have gone through many documents but still confusing me. we have a site to site vpns between two ASA firewalls , so i have disabled NAT-T on asa firewall but still both sites are communication each ...
Hi Guys, Hoping someone can help we have an satellite office connected back to us over 2 Metro Ethernet links 10Mb & 20Mb, for where we present internet transit. I have 4 cisco 2901s on each side of the links and tried using GLBP, to fully utilise ...
Hi Experts, I need some help from you to understand how the software queue would work in a situation where shaping with nested queuing is applied on sub interfaces. I understand that eacch Interface has a buffer that it uses to queue excessive pack...
Hi I have a Cisco switch and the utilization is going crazy, i have ensured that line con 0 does not have logging synchronous as it was identified to sometimes cause the high utilization (Cisco bug ID CSCed16920 or Cisco bug ID CSCdy01705). I have ad...
Hello Experts we discuss about BGP return traffic issue is comes actually i have 3 ISP links it is connceted on single router i have adverties only one ip public pool ex. 103.205.x.x/24 ISP 1 =20 mb ----active ISP 2 =4 mb ---- passive ISP 3 =4 mb ---...
I am in a new environment where I see few ASR 1002-x series routers. I wonder how I can make sure these are on which ESP license level. Is there any command I can run and verify? Thanks, Josh
Hi All, Is it possible to set a preferred path for a route on 2 neighbors connected on the same vlan using OSPF point to point? Since the outgoing interface is the same for both peers I am unable to manipulate the path selection via cost. I have t...
Hi everyone, I hope someone can help me with this one... Everything appears to be working correctly but there's a problem with the inside static NAT rule. The specific problem is that no traffic is coming to the host from 105.102.10.15. It sends traf...
I am trying to design a way to use one router to terminate VPN connections, and for security reasons, keep traffic separate. So one internal interface is in vrf trusted, where I want to terminate a host of VPNs, and the other interface is in vrf unt...
Hello; I want to share with you an issue I have related to bgp multipath load balancing. My routeur have 3 path BGP with the same AS hop (different AS number but same AS hop - 3 hops to reach destination) to reach one destination, multipath-relax is...
Hi guys, need some help. I need to replace a VPN concentrator - old Cisco 2600, new Cisco ISR 800 What is the best way to proceed with such a task?
would like to run BGP with 32 bit (6 digit) AS number but current verion (s3223_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF17b, does no support can you anyone confirm the exact IOS that will solve my problem ? I have 7604 having "WS-SUP32-GE-3B 9 ...
Experts, This Field notice has greatly impacted our operation, we have multiple sites running this IS Router, A bunch of cases whereby we have RMA but still given us the affected version which is V02. http://www.cisco.com/c/en/us/support/routers/4...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM | ||
05-05-2025 11:47 PM | ||
04-22-2025 12:20 PM |
User | Count |
---|---|
9 | |
7 | |
4 | |
4 | |
3 |