Routing

Hi all I'm new to Cisco world and just finishing CCNA with little experience in Cisco devices so any advice would mean the world to me. I was given a task to create Site-to-site VPN with two Cisco 891F routers. The problem is that one site has a st...

Hello  I have a question about the difference between Fixed Routed Port and SPA-10G Ethernet Module below http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/shared-port-adapters-spa-interface-processors/product_data_sheet0900aecd807...

Hello ,  We are working to extend iBGP connectivity. Since have to execute the changes in production environment. Requesting all your help to check & advice. Current & Working Setup -    We are having three /24 IP pools- 1) 10.10.1.0/24 2) 10.10.2....

Hello, A while back I remember reading about a feature available for ASR 9000 that would allow the same basic functions as VDC does for Nexus but a virtual router context for ASR. But now I can't seem to find any reference to it? Did I dream that I ...

I've been advised to add BFD to my CoPP policy, as currently that traffic is handled by the data plane. Can anybody explain why BFD isn't in the CoPP by default given it's importance? I'm sure there's a reason and would like to understand before mak...

Folks, I have 3 ISP WAN links, which service is provided by three different ISPs. I currently have my static routes as the following: 0.0.0.0 0.0.0.0 10.1.0.1 10 #wan1 0.0.0.0 0.0.0.0 10.2.0.1 20 #wan2 0.0.0.0 0.0.0.0 10.3.0.1 30 #wan3 How can I ke...

I was trying to set a route community while advertising a network in BGP in this manner. ! route-map Loo0 match int loop0 set community 300:10 ! router bgp 300 network 6.6.6.6 mask 255.255.255.255 route-map Loo0 This however does not work. The solu...

Today we decided to give release 3.10.1S a try on our least loaded ASR1002 (which we use for PPPoE).  The device has two GbE interfaces in a port-channel (per-vlan manual balancing) and the first thing I noticed after the reload was that one of those...

I have a few 3650's here stacked. One little problem is that I have one client with 2 servers, each server is hitting about 70-80MBps consistent (even on 100 speed port). Is there a simplified way to reduce the max to about 50Mbps without affecting h...

Hello, Equipement: CISCO2921/K9 Cisco 22921 is used as Customer Edge I have one interface g0/0 which is configured with subinterfaces (g0/0.200, g0/300).  g0/0 haven't IP adress but each subinterface have IP address. interface GigabitEthernet0/0 no ...

Hi guys, I have a BGP point to point connection over a 100Mbps link between Branch office and Main office, connection via ISP. I have set up under two cisco routers 2801 with advance security ios a GRE tunnel running ospf protocol so I can share mu...

Hello, I've got a Cisco 887 (C887VA-W-A-K9) router connected to an Ethernet WAN service. I know 887s are typically meant for DSL connections, but the customer didn't want to spend money on a new router. The ISP requires that traffic is shaped on the ...

Has anyone been able to install a linux on the embedded service engine ? I can only find out it runs CIMC-E and there's mention of linux, but no actual example on how to put in linux. Regards.

First, I appreciate the help I've received in the forums here. Thank you in advance, again! Set up 2 x 3650 L3 switches recently and want to double confirm the following if true or not. Secondary power modules can be installed hot swappable, no ne...