This is the error log of a Cisco 1841 device :Syslog logging: enabled (0 messages dropped, 3 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)No Active Message Discriminator. No Inactive Message Discrimina...
I recently installed a memory license upgrade (FL-8XX-512U1GB) on a c891F ISR. The license install <filename> command reported successful installation. However, a show version command still reports 512MB of memory and the license information doesn't ...
On a 2911 with a VWIC3-1MFT-T1/E1, is there a special configuration that I need to do to make it data-only? We don't need voice yet, and all the configurations that I've seen as I read through hundreds of posts talk about configuring the card for vo...
I'm going to try to keep this simple, but if need be I can map out a topology or upload some configs to look at. Thanks in advance for the help. 2 sites - one for production, one for DRBoth sites use same AS, both sites have same ISP.Production and ...
Hi, I have a backup ADSL connection on a Cisco 1921 and have a block of 8 IPs from the my ISP. - Is it possibe to assign one of the static IPs to the LAN interface of the router, which will then connect to a different firewall/router to do NAT?, i.e....
Hallo,I have a cisco router and ASA. The internet link connects to the router first and then to firewall. I have two internal web servers one of them is HTTPS and one is http. 192.168.11.112 is my HTTPS email server and currently it can be accessed ...
I want that R5 knows a route to the subnet 192.168.8.0.Configuration of R1:interface Loopback0 ip address 192.168.100.1 255.255.255.0!interface FastEthernet0/0 ip address 192.168.8.1 255.255.255.0 duplex auto speed auto!interface FastEthernet1/0 ip ...
Well, on the 19th of September we had two of our 1801-M devices fail to restart after a power-cycle due to the documented 'memory degradation' issue documented here: http://blogs.cisco.com/news/ciscos-commitment-to-customers/Fortunately Cisco have de...
Hello All, We have a network of a L3 switch, an ASA firewall,a router,L2 switch connected to some servers.All these are connected through inter-vlan routing.In this scenario if i run any routing protocol what will be the advantage of that?How data t...
I am working on a DMVPN with 10 spokes 2 of those spoke are redistributing eigrp. So my the internal dmvpn route is preferred.Any suggestions!!!!!!!! without creating another eigrpI changed the distance to 171 on eigrp one site it somehow workedKnown...
Running 15.4(2)S on the ASR 901. Trying to do a simple NAT in my lab. The problem I'm having is that the host directly connected to the router doesn't NAT but if I source a ping from the inside interface it NAT's just fine. Both are on the same netwo...
Hello, guys!I`m trying to find out a SNMP OID of current SIM slot for Cisco 819 router (C819G+7-K9).That is I would like to get by SNMP an output of following command:R-12#show cellular 0 securityActive SIM = 1SIM switchover attempts = 0Card Holder V...
Hi,I have few cisco nexus 60001 (6.0(2)N2(3)), but now I want buy two more. Witch software version I should choose 6.0(2)N2(3), 7.0(4)N1.(1) or older? What is cisco recommended version?
Hi,I need to put a rate-limit on my router WAN interface. I need to give a certain cap limit for respected clients. My question is, if that cap is not being fully utilized, will the rest of bandwidth be available to default traffic.and again, if ca...
Hi I'm setting up a Cisco 887 ADSL/VDSL router at home.I have the ADSL2+ Annex A side up and running.Cisco_887#show ip int briefInterface IP-Address OK? Method Status ProtocolATM0 unassigned ...
