Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
HiI have this Ethernet/Token Ring Router and would like to know howto put the interface TokenRing0/0 up?ETHTR#sh versionCisco Internetwork Operating System SoftwareIOS (tm) C2600 Software (C2600-I-M), Version 12.2(5d), RELEASE SOFTWARE (fc1)Copyright...
We have a 3600X ME acting CPE with per vrf BGP towards a PE router.Pxe boot for clients on vlan interfaces in the vrf's does not work, while DHCP relay works just fine.We have both the DHCP server and the PXE servers addresses defined as ip-elper add...
Please provide me why my router rebooted?reason is: bus error at PC 0x23B1F92C, address 0x3CWhat does this mean&show ver:Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)Technical Support: http://www.c...
Hello,I tried to post this question the other day. I updated the diagram to give a more accurate view of what I wan to accomplish.I want to tunnel a VLAN across the WAN but, I want to connect to the Provider with only one link. I want the VLAN and th...
I have configured Router 1 as followsint gi 0/0.10encapsulation dot1q 10ip add 192.168.10.3standby 10 ip 192.168.10.1standby 10 preemptstandby 10 priority 115and Router 2 asint gi 0/0.10encapsulation dot1q 10ip add 192.168.10.2standby 10 ip 192.168.1...
Hello,I nornally track an interface line protocol when I set up HSRP, but today I noticed a router trackign "sla 1" what is this as there is no reference to it anywhere else in the config:track 1 ip sla 1!interface GigabitEthernet0/1 ip address 172.3...
I have this configuration in many routers:ip local pool COMPANYVPN_POOL 172.30.255.1 172.30.255.254crypto ipsec transform-set COMPANYVPN_SET esp-3des esp-sha-hmaccrypto isakmp client configuration group COMPANYVPNkey <company_password>dns <company_dn...
Hi, Is it possible to pass 802.3 packets over a L2TP?If so, how would the tunnel differ from a normal L2TP?Thanks,
Hi All,I asked this in the ASA forum, but also looking for the Router equivalent.I'd like to see if a Router/ACL is blocking / dropping traffic when I try to connect to a server. I'm basically getting timeout errors every so often, and want to see if...
Hi Guys,I have a requirement where I need to NAT the destination IP address of traffic that is from two different sources.For example, If either 172.31.50.1 or 172.31.50.2 send traffic to the destination 172.31.164.48, I require the destination IP to...
Hi all,we have a Cisco7206VXR with NPE-G2 2 GB RAM 256 MB FLASH.Now there is a need of a SA-VAM2+ Module.But the Module is after Booting not "enable" and the Mesage appear:%PA-3-NOTSUPPORTED: PA in slot2 (Unknown (type 1200)) is not supported on this...
Hello,Last night we tested our BGP failover and it was a a success, Here is our setup:Dual ISPs (one priamary, one for failover only), dual routers. Router 1 is connected to ISP1 and we advertise our class C out this router and recieve a default rout...
Hi,when i am typing debug ip ospf * (events, hello, etc) in cisco router, I am getting output nothing. It has two neighbor established and working on the same router.what could be the problem....?thx.Franco
Hi All ,Please tell me any field is there in OSPF packets to specifty the network type .How OSPF is detecting network type mismatch.For ex: one side having point-to-point and other side is broadcast.thanks,Arun
Currently i am doing below test. Can anyone please provide the configuration for double tagging ?SETUP====== BRAS1 BRAS2 1/15 2/6 | | | ...
| User | Count |
|---|---|
| 17 | |
| 13 | |
| 9 | |
| 8 | |
| 7 |
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
