cisco-881, Version 15.4(1r)T1(obfuscated)cisco-881#traceroute 1.1.1.1!! output ommitted !!4 theisp.net (7.83.1.8) 24 msec 16 msec 20 msec5 4.15.1.59 16 msec 4.15.1.63 16 msec 4.15.1.57 16 msec6 * * *7 * * *--- Question: What does it mean that the...
Forum Posts
We have query from the customer what the test environment when cisco Catalog below says in C1111, "the IPsec throughput with the SEC license is 50M"(in Japanese) but what verification method (packet size) or setting was used to Cisco? シスコ製品カタログVol.15...
Hi,According to the definition my router should also display the Webui. But I only get this display:Router: C931-4PIOS Software: Version 15.8(3)M6Does anyone have any idea how I can enable and call WebUI?Bob
So I'm supposed to "Configure route to the 172.16.2.0/24 network via 172.16.1.50" and "Access web page at 172.16.2.100" I am pretty new to IP routing so I need some help with this. I put in the command "ip route 172.16.2.0 255.255.255.0 172.16.1.50" ...
Resolved! OSPF path selection
Hello I have a problem that i am receiving prefix on a router with ospf from 2 direction ( primary/ backup ) devices and it should be preferred using metric in the redistribution statement as below the problem that the metric isn't seen in the route...
Hi all, We have few ISP providers and few public subnets. we need send/receive one specific prefix traffic via one ISP provider for any destination. For Inbound traffic, I can use AS-PATH prepend option. But I have a concern how to control outbound...
Hi allim currently doing the spcor course.they talk about mpls te using ospf etc.how is this used when we have bgp mpls vpn’s?does mpls te just build the best path via igp to the loopbacks and then bgp just uses this path ?how do they tie together ? ...
Hello All,I'm currently labbing in EVE-NG with a Nexus 9k and some ASAsI'm able to ping from within each LAN behind the 9k to the external WAN interface on the same 9k, however I cannot get traffic to forward to the next hop whilst having a route to ...
Hi, I am working on a design situation where I want to advertise the OSPF default-route towards the same router from where it was learnt but with a higher metric. The use case is if the site looses its site-local internet then it uses the cross site`...
Hello.GOAL: to add static routes so a www server will be accessible to the LAN through a backup VPN if primary VPN fails.My strategy:1. From the primary VPN gateway, inject the main static routes, then redistribute into EIGRP (default will make these...
Hello. Simple quick question... When I'm trying to find the source of a route (especially EIGRP), my method is to laboriously sh ip route x.x.x.x then get that next hop data, then SSH into the next box and repeat until I reach the source. Is there so...
Good day, I am having a problem with a configuration with the Cisco 1111-4LTE. What i am trying to do is use WAN 0/0/0 as my primary WAN, and 0/0/1 as my secondary WAN, as well to have The LTE option incase both of the WAN's are down the router would...
Just a curious thought about AS_PATH. The way loop prevention works in BGP is that if I see my own AS in the AS_PATH attribute, then I discard the route.My curiosity is this ... why did my neighbor send me the route in the first place? He knows my ...
So there is my setup (IOS-XR 7.2.2): Nice and simple. Running OSPF between them. This is the config: hostname R1 ! interface Loopback0 ipv4 address 10.1.1.1 255.255.255.255 ! ! interface GigabitEthernet0/0/0/0 ipv4 address 192.168.1.1 255.255.25...
Hello.2 weeks ago I in an EIGRP network I erred by executing a "#redistribute static metric 500000 1 255 1 1500" command in an EIGRP network that mostly if not entirely used a route map. This mistake maligned the routing table, and many connections w...
