Hi, I just power up 2 units new Cisco ISR 4321 and smart license is turn on by default. Both router is using IOS version 17.3.5. One router is purchase ip base plus UC feature license and another is purchase ip base license. On my virtual account, I ...
Forum Posts
Resolved! Mesure of jitter based on ping command
Hello,I would like to measure the jitter based on ping command. From the ping command, I get the round-trip time. I'll get the latency by dividing the average round-trip time by 2. Then, I want to calculate that f.e. for 30 packets, and then calculat...
Resolved! VLANS and the details
Hi all, not sure if this is the best location of the community but here is my question... Probably a easy or silly one for many but... I would love to find some more clear, simple and qualitative explanation of how Vlans do work. All the definition a...
Hello, In my network, ISP is providing 2 ILL lines with different IP addresses. ILL1-200MB AND ILL2-100MBBGP IS Configured, but in LAN poolside (customer interface) configured in one interface.but in LAN both ip not getting the same speed... not conf...
Hello I was trying to set up two sites with a router at each site. There is a layer 2 switch that is connected to each router and they are connected to hosts. I set up a gre tunnel between the routers and set up ospf between the networks. There are a...
System Configuration:SR-A (master) : Server-1 (active-standby mode) | outside | 192.168.0.100 | mac id- aaaa.bbbb.cccc SR-B (stand-by) : Server-2 (active standby mode) | outside | 192.168.0.100 | mac id- aabb.ccbb.eeeeASA-1 : Cisco ASA 5510 firewall ...
Resolved! Switch time non-sync
Hi, I am currently working on an Industrial Switch. I have updated the clock using the clock set command. The show run gives why is the last configuration time not in line with that of the switch?Any suggestions to correct this?
Hi guys, cisco 4321 router rebooting continuously. So i did console login physically , it is showing like this icon ################################# . Nothing showing . So how i take logs before rase a TAC.
Hi there,i need help to configure a new 200mb connection with ipoe .Situation:KPN ISP with lighting edge 310. The KPN doc says they need two interfaces: GigabitEthernet0/0/0 for the WAN (KPN side) and GigabitEthernet0/0/1 for the customer sidei insta...
We have IPSEC tunnels between different DC and its working fine with static routing, For Dynamic routing i have configured OSPF in between them one end is Huawei and other end ISR4400, On Huawei end i can receive and send Hello packets but at ISR end...
The traffic between the loopback 0 interfaces of R1 and R2 should traverse through R3; R3 should be configured such that it translate 132.10.10.1 to 171.1.1.1 and 132.11.11.1 to 173.2.2.2 You can do NATTING only R3 router. After completing the sol...
Hi GuysA quick question, we have some Cat 9K switches with Network advantage licences.Are there any limitations when it comes to running BGP on them?We want to just receive a default route and do some basic route maps tuning on them.We are currently ...
Hi,I'm building a packet tracer network (see attached image) and had a question on putting ACLs in place to control interVLAN access [noting HSRP is set up on both distribution switches for redundancy].VLAN 21 10.20.21.0/24VLAN 27 10.20.27.0/24VLAN 8...
Resolved! BGP route padding on Cisco ASR
Hello, I have two ASR routers running BGP between two connections. I am new to this so please bear with me. Basically we are running BGP at our hub office and would like to pad routes to certain branch offices to connection A or B. Is it possible to ...
The role of all data-link protocols is to control the correct delivery of data over a physical link of a particular type. For example, the Ethernet data-link protocol uses a destination address, which is the MAC address, field to identify the c...
