In an ASA 5525, I need to add a second circuit (different source and destination) to run through a policy based L2L VPN. May you please tell me if below config will succeed in my intent? (or does the whole config need to be on one line?) ... OLD CONF...
Forum Posts
I'm attempting to reset an ASR1001-x and I am able to clear everything besides a directory called 'webui'. delete /force /recursive doesn't do the job. After every attempt to delete I get the message <file or directory does not exist> Is there any so...
I recall when there was the USB > RJ45 console cable, there was a driver needed to make the PC recognize the cable and create a COMM port for it. Now, there is the USB > USB-C console cable. Does it similarly need a driver, or when it is connected to...
Hello, I am looking to advertise same public /24 from two locations with BGP setup. SiteA connects to SiteB using MPLS by ISPX SiteA BGP adv Public IP say 192.168.1.0/24 to ISPASiteB BGP adv Public IP say 192.168.2.0/24 to ISPA Can we advertise the p...
Platform : 2911 with ios 15.7(3)Situation: Tunnel to a central platform over a physical high latency carrier.Issue: "The sum of all queue-limit value is greater than the hold-queue value"The exact error is: %QOS-4-QLIMIT_HQUEUE_VALUE_SYNC_ISSUE: The ...
Resolved! NAT via 3 connections using ip sla track
Hi!I had a difficult task for me.I need to configure NAT for three different connections.We have 3 communication channels with our partner: interface Port-channel1.10description PARTNER_CONNECT1encapsulation dot1Q 10ip address 10.10.0.2 255.255.255.2...
Resolved! Can't access crash file on 4431
Not exactly sure what I am doing wrong here. I have a 4431 that crashed server times a few days ago. CUBE-RTR uptime is 2 days, 17 hours, 5 minutesUptime for this control processor is 2 days, 17 hours, 6 minutesSystem returned to ROM by Critical sof...
It seems that the generic C900 manual does not 'match' the command set in the C921.show running-config is not supported in my router.Can someone point me to a manual that details the command set available tot he C921-4P?
Hi,Please can anyone advise on the C8500L-8S4X BTU/hr value with 2 x PWR-CH1-400WAC PSUs installed?Thanks in advanceRassic
I have a Cisco IR1101 router with a Network Essentials license. Previously I have setup the router with a VPN and shipped camera traffic back to our main location. However, I have since found out that across the VPN camera traffic is not supported ...
Hello community,I need help with understanding of what "redistributed in" and "advertised by" really means in "show ip route" output. Originally, I thought that "redistributed in" means that this particular route exist in particular routing protocols...
Hello folks.I'm trying to allow end devices to communicate between vlans. I I'm using a Multilayer Switch 3560 24 port. And 4 computers. 2 per vlan. NAME VLAN IP PC10_1 10 10.100.10.50 /24 PC10_2 10 10.100.10.51 /24 PC20_1 20 10.100.20.50 /...
I want to access two machines having the same IP addresses, I have narrowed the requirement by using VRF and route leaking but am stuck on the natting part, I wanted to do natting within the VRF, where one of the VRF interfaces will act as an outside...
Hi, I have the below topolgy . Now I want to convert area 50. How can I minimize downtime . for example if I am changing switch3 to nssa other ASBR (vios4 ) neighbourship should not go down )The default route injected from the area 0 , If I...
hi,my google search is failing me.just would like to confirm if i can upgrade my NCS 540 from IOS-XR 7.2.2 directly to 7.4.2?what's the difference (pros and cons) using the#install add source /harddisk:/ NCS540-iosxr-k9-7.4.2.tarversus installing/upg...
