Routing

I have an issue where my bgp logs are not being sent to a syslog server. I am getting %SYS-5-CONFIG_I: Configured from console by user on vty0 (x.x.x.x), so there is proof logging is working. Howerver, when I do a clear ip bgp A.B.C.D the following a...

Does anyone know why the bandwidth statement on the subinterface would be ignored unless its applied to the main interface? In a head-end setup i may have additional subs and I would think the bandwitch statement on the main int should reflect the ac...

Having issues getting CBAC to work - does my confiuguration also require an ACL inbound on the port config below that does "deny any any" etc. then CBAC uses this ACl top open ports selectively etc,.interface GigabitEthernet0/0 description DS-WAN ip ...

This is my scenario.  I can access the LAN environment 10.1.1.X from 20.1.1.X but cannot get out the gateway to the internet?Any ideas? The linksys gatway model is a WRV54G.I am mystified.~Peter

Hi,Our customer is willing to buy a device to "hide" their applications configuring NAT/PAT. He currently have 40 applications and 20 VLANS.Is a CISCO3925 the most appropiate device for doing this?Thanks in advance for any help!

Hey,I can't find documentation on this message:*May  8 10:05:06: Tunnel114: adjacency fixup, 10.100.111.4->10.100.11.21, tos set to 0x60Does anyone know why these messages show up and what they imply for routing through the GRE tunnel?Thanks,Joey

Hi, I have a 5505 ASA at a remote site. There are two subnets behind this firewall. The directly connected one is 10.10.33.0/24 and the other network 10.11.33.0/24 is one hop away from the firewall. The "inside" interface address of the firewall is 1...

Hi all, i've some problems with interworking ethernet to vlan with l2tpv3 on es+..L2vpn interworking ethernet to vlan over l2tpv3 seems not working if 7600 es20+ performs Ethernet Interworking. It seems that Es20+ doesn’t add vlan tag from pseudowire...

Hi allI have a requirement to build a site to site tunnel to my head office from a remote office. My question is, should I use an asa the other end, or should I install a router with a zoned firewall and use a vti tunnel. Can I create a vti tunnel on...

Hi all, I have been surfing the net for whole day long but i couldn't found out what are the differences in between dynamic pppoe and static pppoe.Could any experts out there provide me some guides please? Thanks for help ...

OSPF is  link state routiing protocol , any change in the topology is updated by th lsa at the moment change is happened and LSDB is updated, if there is no change in the topology  why OSPF is refresing the LSDB  after every 30 minutes RegardsBinoj

Hi all,I'm trying to troubleshoot a intermittant dsl issue, on a Cisco 887VA IOS 15.2(3)I'm not sure if it will help but I would like to view the dsl training log. In IOS 12.4the command to enable this was:"sl enable-training-log failure"   under the...

Hello,I have setup a Cisco SR520W and everything appears to be working. After a few hours, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device.If I unplug and then plug in the network cable connecting the WAN ...

Hello,I have setup a Cisco SR520W and everything appears to be working. After a few hours, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device.If I unplug and then plug in the network cable connecting the WAN ...

hi two routers are connected  and ospf is enabled , after creating adjacency , how router is knowing that hello packet is a just a hello packet  to keep the adjacency up  . RegardsBinoj