Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10276 Views
  • 7 replies
  • 16 Helpful votes

I'm sure it's something simple, but I can't for the life of me figure out why our new connection isn't working.We have a Main office with a connection through our Internet service providers TLS (transparent lan service) connection to a shop location,...

"hi allHow to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them. Can s...

Resolved! Routing design

Hi All, Can you please give me your suggestions for the below setup I have network in a triangle setup, each router have a primary and one backup link, I plan to run EIGRP on all the links and IP addressing as below  Between R1 and R2 both primary an...

I have the following setup. Router1 is connected to MPLS provider1. We are doing BGP to the provider and EIGRP internally. Switch1 is a layer 3 switch and is doing EIGRP STUB routing. I am receiving all of the routes from provider1 to Switch1 from EI...

HiI have run in to a problem with EIGRP and redundant configuration.We are about to migrate to a solution with existing hub and spoke routers but this time we will add redundancy at the central site.The connection between the two central Hubs and the...

a.hed by Level 1
  • 1478 Views
  • 7 replies
  • 0 Helpful votes

I'm hoping someone can help me with the maths to reconcile what I've observed onour routers  on a tunnel interface.  The maximum amount of data I can get across the tunnel is 1339 bytes, which seems just a little bit too small.Background: we have two...

Hi Guys,I need help on a sample configuration for internet failover . i  have 2 ISPs with one coming in thought a serial cable and another thorugh internet and would wish one take over after the other has failed .The router is Cisco 1921 .

I'm migrating the configuration from a Cisco 12416 router running Cisco IOS, to a CRS1 router running IOS-XR.In IOS I have configured the following command for FRR "ip rsvp signalling hello bfd". I cannot find the way to configure this parameter usin...

jbaraona by Level 1
  • 5733 Views
  • 7 replies
  • 0 Helpful votes

We have recently migrated our core router from a 7206VXR to an ASR1002-F, following the migration we cannot assign specific OSPF costs to individual spoke destinations as the "neighbor x.x.x.x cost nn" command is not supported on the ASR.Any ideas ho...

hmdavies by Level 1
  • 3935 Views
  • 15 replies
  • 0 Helpful votes

Hi all,i have 2 applications running on my PC (10.30.2.11) to get video flow from a remote source on the WAN (10.31.2.9).But application1 is not getting the video flow and application2 is getting it.i have collected debug logs on router 1 ( which is ...

Hi, imagine I need to execute the following task:a)Using a policy-map, assign video traffic a DSCP 56.b) Now define a policer for the video traffic with rate of 3M and a burst size of 1M. My question is:In order to enter the "bc" value in the router ...

news2010a by Level 3
  • 691 Views
  • 0 replies
  • 0 Helpful votes

HI,I have got a Cisco 3945 router. I would like to know which IOS image I can use?It should provide meBGPHSRPTUNNELsSLAsACLsENCRYPTIONand it should bebug free.Please suggest an image.

Resolved! nat question?

Greetingif there is possible, to nat a private ip to public ip on cat6500, and only on the case the another ip address is speciafied.for example:      if 10.1.1.99 was a internal private ip, and 10.2.2.100 was a public internet equipment. I am hoping...

julxu by Level 1
  • 771 Views
  • 5 replies
  • 0 Helpful votes