In this topology Routers are configured as given in the diagramRouting Protocols used,B/W R0, R10, R7 ospf i have configured tap4 using iptables to nat and forward the traffic to my physical network adapter, which is connected to internet.my question...
Forum Posts
Hello,I recently added another RP to our PIM Sparse-mode Network. We utilize BSR. This may've had adverse affect to our ACI Border Leafs but I wanted to be sure from a Multicast Perspective, I can add another RP Candidate for a specific Group? Along ...
I remember a while back I saw a doc about following restriction in similiar wording about port-channel/etherchannel supportiveness on the ISR 4K. "It is not supported to build an etherchannel with member ports from different modules." I have a 4451-x...
Resolved! Router C8300-2N2S-6T Management Port?
The company bought 2 C8300-2N2S-6T and I'm reviewing the Cisco information for this Router and I can see that this Router has 4 UTP Port but one of this port is for management purpose? According to Cisco the Interfaces built it with this Router are...
I've seen a problem at work which I'd like to simulate, but am wondering how best to go about the build.The situation: a streaming media application handles tcp packets out of order by discarding and requesting retransmit. This causes major slow down...
Hi All, As I have checked logs at AR2240C router, getting consistently error like - SSMPADP/4/AUTHENTICAL_FAIL:OID 1.3.6.1.6.3.1.1.5.5 SNMP authentication fails. %%01SNMP/5/SNMP_LOG_IP_UNLOCK(l)[252944]:The IP address of request message was unlocked ...
ASR 1006 show platform software status control-processor briefコマンド結果のStatus（Healthy Warning Critical）について閾値は何パーセントでしょうか。例Healty 88%以下Warning 90%以下Critical 91%以上等
HelloI have a finger print machine, I want to connect it through internet remotely so I must make port forwarding in the router which is CISCO2901/K9, I did but it will not be opened still by checking in this website(https://ping.eu/port-chk/) by usi...
Sample Diagram here. The dual ISPs network that I am working has an interesting setup. In Router 1, here is a partial config ip route 67.29.128.153 255.255.255.255 50.50.50.2 partial show ip route Gateway of last resort is 67.29.128.153 to netwo...
Question about upgrade of the ASR-920-4SZ-AIf the rommon is upgraded to the lastest version are there any problems going from 15.x (eg 3.18) directly to 17.3.7 ?or do i need to step through 16.x first?
Hi guys, can you please tell me how to downgrade IOS-XE on Cisco ASR 1009-X?I need a step by step guide because I lack knowledge.
Hello all,We have an ISR-4331 that is running IOS XE 3.16.09.5 and need to get it upgraded. I see that both 17.6.3 and 17.3.5 are recommended releases. I did see that a ROMMON update is required. Besides that, would we be able to upgrade direc...
Hi guys, I am having issues in adding new entries to an existing access list, When i add the entry to access list and then issue #sh access-lists The new entries are at the end of Access List but i want them to appear on the top or in a place wher...
Trying to get my head around a switch I have at the moment.Show inv says its a PID: WS-C3850-48U-SBut the product code sticker on the switch says: WS-C3850-48U-LI know the different in regards to both switch's specifications but unsure to why it woul...
HelloI was advertising an aggregate address of of 10.31.0.0/16 I have 2 other network statements that match both a directly connected and OSPF learned prefix (10.31.0.0/30 & 10.31.32.0/24).Using a different device on-site, I advertised 10.31.129.0/24...
