Routing

Hi All, I have a HQ and a DC site. I've subscribed 2 links going to the same MPLS provider. My local site AS number for this 2 link is the same. I've intended to route all subnets on link 1 and in case of link 1 goes down would like to automatically ...

Hi,Our one of the Client need to replace CISCO 831 router with high end router , there will be around 60 to 70 users accessing this router for Internet surfing. Right now 831 having 3 Ethernet and 4 Fast Ethernet Ports.Could u suggest one of the mode...

Hi,Iam trying to make L2tpV3 tunnel between two PE routers with IOS as below:PE1: 12.4(15)T7PE2: 15.1 however if i replace the IOS on PE1 from 12.4(15)T7 to 12.4(24)T4 the l2tpv3 session comes up with no configuration change.Is there any compatiabilt...

Hey Guys,I have enabled port mirroring on a 6509 but for some reason the destination port is not showing any traffic. Configuration is pretty straigh forward and the destination port is howing (up down (monitoring)) which is the normal operation. I a...

Hi,I have a requirement to provide stats on a per-department, per-destination basis between sites. If I take Voice as an example I have 5 child classes referring to the 5 departments each matching EF and a particular access-list that matches the depa...

First post... sorry if I'm in the wrong spot.I have multiple sites on a Sprint MPLS network.  They're handling QOS on their network and have given me DSCP numbers to use for QOS.I'd like to tag packets based on their destination IP.For example:Subnet...

Hi Folks,Need your expertise regarding the configuration for bgp multihome single ISP dual router failover. I am in situation that I need to setup configuration as quickly as possible. Below is the scenerio:-------------------------------------------...

Hi all,I've run a across a strange issue that I've not encountered before and after the things I've tried am beginning to think it's a limitation of the router itself.  What I have are 3 Cisco 1941 routers that are all endpoints for a customer's MPLS...

Hi all! What is real IPSec performance of ASR1000-ESP5 ? I found on http://www.cisco.com/en/US/prod/collateral/routers/ps9343/data_sheet_c78-450070_ps2797_Products_Data_Sheet.html: Cisco ASR 1000 Series 5-Gbps ESP Module Performance and Scaling - 1.8...

Hey everyone, We got 2 ISPs -------> two ASA 5520 Primary / secondary --------> LAN .ASA is configured with ACL and Static NAT for our mail , web & ftp servers .My question is how to configure the 2nd ISP on the ASA to auto switch to the 2nd ISP when...

Hi all,I am trying to assign bandwidth for two different clients using CBWFQ, I use a class map to call the address of each clients defined by an access-list. MY OBJECTIVE IS TO ASSIGN 128KBPS FOR EACH CUSTOMER WITH LEAST CONFIG BECAUSE OF RESOURSES!...

Client is having following setup:1. 3 floors2. each floor is having 4500 series switches 2nd-4th floor3. 2nd floor is having core switch 45104. all 4500 series switches is having IP base IOS image5. All are connected to each other in Ring topology wi...

can any one explain the solution to this lab?? Task 1: To begin with, configure the  hostnames on routers R1, R2, R3, R4 and Sw1 as illustrated in the topology. Task 2: Enable the Serial interfaces of  R1, R2, and R3 for Frame Relay encapsulation and...

Hi,I am running EIGRP Protocol on my network. I came to know that some of my routes learnt by EIGRP are getting disappeared after sharp 30 sec of interval. I also observed that 2 of 3 routes from one router are disappearing and one route is coming co...