Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! will this image fit and function within this router

Hi,I  have an old 1841 currently in a lab setup currenlty running 12.4, but I need to  know without disrupting that setup if this router will (a) run 15.1 and  (b) have any memory left over to actually handle dynamic processes. If  you could enlighen...

lcaruso by • Level 6
  • 1391 Views
  • 8 replies
  • 0 Helpful votes

Resolved! Invalid Window Scale option for session

Can anyone tell if it's a misconfigured host or router causing these log messages ?*Nov  9 01:05:22.807: %FW-3-RESPONDER_WND_SCALE_INI_NO_SCALE: Dropping packet - Invalid Window Scale option for session 172.29.6.99:443 to 209.197.25.16:28230 (Initiat...

lcaruso by • Level 6
  • 7601 Views
  • 6 replies
  • 0 Helpful votes

Problems with Video in/out on an ATM config attached

Can some guru have a look and see why this configuration is not work, 100% it should work, although may be an issue with NAT'ing?Sorry forgot to mentiion at beginning of thread, can video out all ok, and get out to vpn to company and can get general ...

DerekM by • Level 1
  • 429 Views
  • 1 replies
  • 0 Helpful votes

Connecting Two 1841 Routers together...

Greetings,Simple question:For educational reasons (a Videoconference class), I need to connect two 1841 router with each other. They both have HWIC-2T modules, but it's almost impossible for me to have the CAB-SS-2626X Smart Serial crossover cable on...

Hardware differences- 6506 and 6509

I have a 6509 and a 6506- same IOS version and flavor, same hardware, etc.  One supports rate limiting on the VLAN interfaces, the 6509 says "not supported due to hardware".  What is the difference here?  Im very confused on this since I was under th...

ospf route update

Dear bossI m using ospf between HO and Branches for two links. branch router are 2811 and HO router 3845. when i enable ospf at branch i get all branch route like HO router and a default route. My requirment is each branch get only HO but no other br...

Resolved! Default route issue

Hello All,I have a router with the following configuration in fa0.1 and fa1.2interfacefastethernet0.1encapsulation dot1q 10ip address 10.10.10.3 255.255.255.0interface fastethernet1.2encapsulation dot1q 15ip address 10.10.15.3 255.255.255.0and routin...

rouzbehta by • Level 1
  • 1021 Views
  • 4 replies
  • 0 Helpful votes

ASR-1000 upgrade (IOS-XE and ROM)

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tableau Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm...

Resolved! ASR1002 web logon

The loopback of the ASR1002 is 2.2.2.2.When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password....

Resolved! EIGRP Route cost calculation

Hello allI am trying to work out why certain routes have certain costs within EIGRP.All of my eigrp K values are default, so eigrp cost is equal to 256*(10^7/BW + delay)However, in the example below, FD is 312832, yet advertised BW and delay from BGP...

Frame relay help

http://blog.ipexpert.com/wp-content/uploads/2009/08/15.png pls see above link i just want to know can we connect 2 frame relay cloud on one physical interface or we require two physical router interface for it.In above link they use one router interf...

Load more