Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hi,I need some assistance understanding security bundles. I purchased a Cisco Security Bundle, Advanced Security, 64F/256D. part number CISCO3825-SEC/K9. My expectation from this device was that I will get an IOS based firewall with no need for an ad...

Dear Community,In the attached diagram I have include the topology that is giving me a hard time...Both routers in the top part of the diagram (LANs: 192.168.121.x, 192.168.241-249.x etc) should prefer the route in and out of  ARTEMIS to reach the in...

Hi All.We have two wan channels, both connect to MPLS cisco, go in on direction i.e (City-1 to City-2). On first channel no have problem, but on second from time to time we see CRC errors. It doesn't depends on amount of traffic on this channel. We h...

a.telepin by Level 1
  • 2199 Views
  • 5 replies
  • 0 Helpful votes

Hi everyone!We are having an issue here, I will break it down like this.We have a 2960 with 2 Gig interfaces but we are using 100fx SFP's instead of Gig. The reason being that our core switch(cisco 4506) is 100fx. Now we have everything set up correc...

Damon Day by Level 1
  • 640 Views
  • 1 replies
  • 0 Helpful votes

As soon as I connected my ASR 1002s to the Internet and digested the Internet BGP table, I began receiving this message.  I’ve google’d and turned up nothing so far.  I assume I need to allocate more memory to this process.Any help would be greatly a...

I have configured a VPC connection to Amazon. I can connect to it without issue from my lan but I can't connect back to my lan from the VPC. From the VPC I can connect to the outside address for RDP on my firewall but nothing inside my lan. I have se...

sduffy by Level 1
  • 475 Views
  • 1 replies
  • 0 Helpful votes

Resolved! hdlc protocol

hi all, because this protocol use at layer 2 (data link) and not use at layer 3 that mean that the TCP\IP model not work with IPX OR APPLE TALK MODEL??i not fully understand how it realy work please help metnx...

davidamar by Level 1
  • 1670 Views
  • 2 replies
  • 0 Helpful votes

Hi ThereI am banging my head against a wall here with this problem....I have a back to back frame relay set-up and the PVC status is Active and LMI is passing messages, however I am unable to ping the peer router.I don't have a frame relay switch, so...

I ran across a config that said this:class-map match-any cos3 match  dscp af31 match  precedence 3 match access-group name voice-controlpolicy-map wanqosclass cos3  bandwidth 200  set dscp af21In this configuration, is the router taking traffic tha...

reviewing a customer/vendor qos set uppolicy-map voice-policyclass voice  (matches EF)priority 768service policy voice-policepolicy-map voice-policeclass voicepolice 768000 96000 it's the 96000 that I question.  I always understood that on priority q...

whanson by Level 2
  • 1380 Views
  • 11 replies
  • 0 Helpful votes

Over the last few days, ISDN connection would disconnect with just a few seconds of inactivity even though disconnect is set at 300 seconds. Often, clear int bri0 was required to reconnect. Follosing is part of message with the clear command:PANIC!...

rlr685rlr by Level 1
  • 1665 Views
  • 3 replies
  • 0 Helpful votes

Hello All,We were facing high CPU utilization on a Cisco 2821 ( 12.4(22)T ) router. After some troubleshooting we disabled 'ip virtual-reassembly' command on both inside interface and outside interface (internet facing interface). After monitoring th...

rmujeeb81 by Level 1
  • 2344 Views
  • 2 replies
  • 0 Helpful votes

Hi All,I have a router 2951 and IOS 15.0(1)M1.The below is the nat statements are configured in that and all are working fine except the one in red color is working for some time say 5 days and stopped working (not stable).can someone tell me what is...

jopetik09 by Level 1
  • 580 Views
  • 2 replies
  • 0 Helpful votes
Unanswered Topics