Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

Below is the switch diagram. As you can see, sw01 is directly connected to SW02 and sw02 is also connected to SW03.SW01 <-----> SW02 <----> SW03Each switch has three VLAN's.SW01: VLAN1: 10.10.1.1 , VLAN2:10.10.2.1 and VLAN3: 10.10.3.1SW02: VLAN1: 10....

kzhen by Level 1
  • 531 Views
  • 2 replies
  • 0 Helpful votes

hiI need remove a interface, old connection sing bgp. however, I found its ip address act as bgp router-id currently.Could I get advice that if I remove the interface configuration, what happend with the bgp router-id? will it change immediatly? if s...

julxu by Level 1
  • 581 Views
  • 2 replies
  • 0 Helpful votes

I have two issues with router 1841 and I would be thankful to anyone who can help me to solve them.Last week I configured 1841 router in PPPoE environment.The goal was to configure QoS on router to give VoIP traffic priority.I used priority queue in ...

marijanac by Level 1
  • 878 Views
  • 1 replies
  • 0 Helpful votes

HiFinancial module service is outsourced in the organizationCustomized application installed on LAN workstation needs port 9090,9091,9092 to be opened to reach Financial Module Server hosted on Internet.FMS_Server----{Internet}------((R))----Firewall...

helloi have couple of questions.i am using cisco 1841 router1. can i create site to site vpn from my cisco router 1841 to check point FW?2. i am using at my router cisco 1841 vpn can i add one more VPN on my existing router ?thanksgolna

hiany body help me regarding fallowing issuerouter 2821 can not boot properlyit is showingUpgrade ROMMON initializeddevice does not contain a valid FSboot: cannot open "flash:"boot: cannot determine first executable file name on device "flash:"c2821 ...

Right now, I am passing one DNS server from each of my ISPs with the DHCP server for my LAN. I'd like to be able pass the correct DNS servers for the WAN which is currently up. I'm worried that the clients may be choosing the wrong DNS server for the...

ggilley by Level 1
  • 807 Views
  • 0 replies
  • 0 Helpful votes

Resolved! Hello everyone

HelloI have been away for summer break but I am now back in school.I was hoping someone could link me to or explain to me - the major differences in the American and European communication speeds.Why are they so different? What is the difference, is ...

Were we sold the wrong product? We installed 2 NM-1A-T3/E3 cards in our 3845, upgraded to c3845-entservicesk9-mz.124-24.T3.bin, but the interfaces show up as ATMX/0 instead of serialX/0.We need to set up frame relay encapsulation. I can't find ay exa...

wsanders1 by Level 1
  • 1019 Views
  • 2 replies
  • 0 Helpful votes

Hi all,I have set up two router with route port (two router with two links with equal cost) and running ospf to test ospf failover time. I get the result is about 4 sec.Why it so fast. ospf not take 30 sec ?

acbennyma by Level 1
  • 4734 Views
  • 3 replies
  • 0 Helpful votes

I have been tasked with implementing a site over seas with limited information. Only information I have is the router type 2851, circuit type T-1, no ip addressing. and a deadline. The provider tech says that I need to configure AMI D4 and is only av...

Review Cisco Networking for a $25 gift card