How do i find if the DSU value is set to default or not in the NM-1 E3 as i am getting the following error message "dsxpnm_gt96k_abort_rx_mpsc:Aborting Rx mpsc failed". I see there is a bug match for this error. But need to confirm it?
I have Cisco RVS4000 router. I notice that internet connection dropps frequently continously throughout the day. It has became worse after upgrading to the latest firmware (1.3.1.0) /IPS signature (1.4.1).It looks like it is dropping the connection e...
Hi,I have 2 x cisco routers (2600 and 3600), i am connecting Serial Interface of both routers to each other, encap is HDLC,but the interfaces are not coming UP, getting the error when "show ip int serial 1/0" on both routers.Please help to resolve th...
HiI have a problem with 7206VXR CPU:7206A#show processes cpu sorted 1minCPU utilization for five seconds: 30%/2%; one minute: 30%; five minutes: 31% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 281 8444700 705667898 ...
Hi all !I have the opportunity to buy either a Catalyst 2960 WS-C2960-24-S or a WS-C2960-24TC-S.Does any of these two models support simple MAC-fitering, just as can be found in simple home routers (allow/deny lists) ?I just want to allow one specifi...
Hi allI am currently setting up a router for my workplace, A cisco 1800 series, this is to connect to the internet for some clients, what access lists should I put on there from both the in and outside, and should I used cbac etc, an an example would...
Dear Experts,It is a design related query. Please find the attached Diagram.I have 2 firewall & 2 Routers & 2 Switches to be operated in redundancy.My customer is asking connected the cables and configure the setup as shown in the diagram marked with...
Hi ,We are getting this below error message at a 7200 router with ios “7200-jk9o3s-mz.124-25b.binError Messgae: Apr 9 09:51:02: %IP_VFR-4-FRAG_TABLE_OVERFLOW: GigabitEthernet0/0.129: the fragment table has reached its maximum threshold 16 We hav...
Hi all;i want to implement Multicast SM into an architecture with 2 CE Cisco 1841, i did the configuration as mentionned in the Cisco Documentation, and i realize the registration in the Multicast Group 224.1.1.1 with one RP, but when i initiate a mu...
Please find attached my network diagram.When all is normal, "ER01.COLO" provides default route to the entire network via 2 VPN tunnels. Currently the diagram is misleading, as I currently only have 1 ISP (2 cable modems, one to each ER - same provi...
Hi All,I have 881G router and wireless internet connection will be activate with 3G. Now I have to establish the communication between this new site to our DC.But there is no any static public IP.Can some one have any ideas how can achive this.My man...
Dear all,I would like to ask you about Hwic-4esw card. let me tell you about my system.At HQ i have Cisco Router 2811 with Hwic-4esw. on port F0/0 and f0/1 used. so i bought card Hwic-4esw for connect to branch.So from hwic-4esw connect to cisco swit...
Hi!I am configuring a Cisco 2821 router equipped with two WAN interfaces giving access to the Internet.The router is equipped with an ADSL card and an SHDSL card.There are two WAN lines, the ADSL line will be used for browsing and the IPoSHDSL line w...
I have 2 T1's bundled in a Multilink Group. I have a QOS Policy assigned to the Multilink interface for prioritizing VOIP packets. Everything that I read tells me that the serial interfaces themselves should have "no fair-queue" set and I currently...
