Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hello,I was thinking about connecting multiple clients to one router. I'm planning to use a switch, connected to the router. Then use subinterfaces with vlans to connect the different clients. The problem is that because of the switch, I'm limited to...

Resolved! IOS NAT issue

I am trying to create a NAT statement to allow an Internet address to translate to an inside address with all ports open between them.  Can somebody help with some code examples or suggestions.For example 208.7.xx.xx ---> 10.0.107.xxThank you

Dears ,one of my customer is connected through a dot1 Q subinterface on our router , Is there is any way to implement this SLA for his service policy-map WAN-QoS  class http   priority 3000   set dscp af11  class Mail   bandwidth 2000   set dscp af41...

Haris P by Level 4
  • 7158 Views
  • 4 replies
  • 0 Helpful votes

Hi  every body.I  was reading about the broadcast addresses.  Let say we have classB address  172.172.0.0, then 172.172.255.255  will be the broadcast address for the network 172.172.0.0.  How about  255.255.255.255.? how  does it differ from 172.172...

sarahr202 by Level 5
  • 1233 Views
  • 5 replies
  • 0 Helpful votes

Hello everyone - Im a bit confused as to why my NAT overload seems to be working correctly from my router when sourcing from the router LAN interface 192.168.253.254, but the Servers connected to my private VLAN3 are all unable to telnet to the speci...

esturao by Level 1
  • 1193 Views
  • 6 replies
  • 0 Helpful votes

Hi,We are receiving three subnets from external BGP peer next hop  10.1.2.1 expernal BGP peer ID /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-nosho...

HI, i have a cisco ASA 5510 using ASDM version 6.3We have a webserver that is been written very specifically and i was  given super direct "DO NOT DEVIATE" directions.This server has to get traffic from 3 different PUBLIC ip's that we  own. (our isp ...

drssjaken by Level 1
  • 12360 Views
  • 1 replies
  • 0 Helpful votes

Hi, I am trying to create a vlan on the 7206 but I get a "%invalid input detected" error. I am using the command Router# vlan VLAN-ID.BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.1(14)E6Thanks.

hello i am useing cisco 1841 router connected to my server IBM X3550 both interfaces set to 100 MB/Full duplex,even thats i see an input error.what should i do ?i try to change it to speed & duplex to automy server connected to router directly(no swt...

Hi Netpros:I have C2821 to use EoSDH link on fix GE port , I concern that dose it process real 1000M traffic when running routing protocol and Mpls etc..thru it's line speed forward in documentation.thanksHerman

jj-zhou by Level 1
  • 793 Views
  • 3 replies
  • 0 Helpful votes

Hi,If we have 1. two ISP links terminated on two routers               2. these two ISP has given different pool of /28               3. We are BGP peering with ISP router using a private AS given to us by each ISP.In this situation is there any way ...

Hi,The   router is performing PAT   for internet access and I'm trying to enable it as an EZVPN server  Using  the Cisco VPN client, I'm able to connect it and bring up the  tunnel. i  can pass traffic by vpn and can ping the local server but  can't ...

Unanswered Topics