Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! Switch 3560 config-register value

Hi,Configuration register value for 3560 swicth. It  shows 0Xf  is there anything wrong with this value?What is the significance of this value like in router config-reg value which we use to recover the password ?Please share the experience.Any link ...

L2TP tunnel over WAN

I got 2 catalyst 4507 switches connecting over MPLS backbone on layer3 interface (no switcport used on gig port). OSPF is extending routes. Now I want to extend vlan and vtp information from one switch to another through mpls link. I checked l2tp con...

new 2811 config

we are planning to migrate 3 E1 circuits from our 6506 (running CATOS) to a new 2811. I have configured the router but have some questions regarding how I should set up the fax. I have attached 2 config files, one for our existing 2811 (bne-vg-2811)....

thinakraj by • Level 1
  • 795 Views
  • 1 replies
  • 0 Helpful votes

OSPF timers

We'd like to change the default OSPF timers from the default 10/40 to something more aggressive, like 1/4.All the routing devices are 3560's on a fiber ring, running 1 Gbps, so we figure it's safe to do so.Thoughts?Is there a global command to change...

huangedmc by • Level 3
  • 9674 Views
  • 6 replies
  • 0 Helpful votes

access-list in router

Hi,Currently in our network for NAT access we deployed on the 3640 router which some times hang when some spurious traffic generated from LAN or WAN or CPU loadso we are planning to upgrade the NAT Routerfor new hardware we need following feature sup...

Resolved! Password recovery

I bought a 1841 Router on e-bay.Apparently, it has been configured with "no service password-recovery". The console shows: PASSWORD RECOVERY FUNCTIONALITY IS DISABLED, and it does not respond to Ctrl-Break during boot. AFAIK, this router does not hav...

Luisinus by • Level 1
  • 11268 Views
  • 15 replies
  • 0 Helpful votes

Resolved! Marking FE traffic for QOS process

Hallo,I need mark traffic from specific FE switch port on C1802 when in goes thrue Dialer there is done some Qos process.How can I do this on FE 8 if all ports are in BVI1?I tryed IP based marking that is not good in case of DHCP clinets off course.!...

locus2007 by • Level 1
  • 3151 Views
  • 17 replies
  • 0 Helpful votes

Error http request via IPVPN

Hi,I have a problem with our 2 branches accessing http port. Let's say Site B can't access the web server in Site A but Site A can access the web server in Site B. In site A we have Cisco 2811 Router and a Cisco 3560 Core Switch, on site B we have a ...

helios999 by • Level 1
  • 713 Views
  • 2 replies
  • 0 Helpful votes

Resolved! BPDU detection

Hello,I need to prove that BPDUs, are exchangeed between my two switches.Here is the situatuion:SWITCH 1 port 1 ------ PROVIDER1 NETWORK -------port 1 SWITCH 2SWITCH 1 port 2 ------ PROVIDER2 NETWORK -------port 2 SWITCH 2Problem is that I have a loo...

datacenter interconnection doubt

Hi,I need to interconnect two datacenters through a IP/MPLS network. I need to exchange the DB information between them and I see it's possible to use the EoMPLS technology for.The problem is due to the fact that I don't have the SPA module with SIP ...

gpangallo by • Level 1
  • 533 Views
  • 1 replies
  • 0 Helpful votes

Resolved! MGX to MGX packet Loss.

Hi Friends,I am facing packet Loss problem with MGX to MGX connectivity. I have an IMA PNNI link between two MGX. I also have a UNI connection to two routers. the connection diagram is provided below.Router1 <-> MGX <-> MGX <-> Router2when i ping fro...

Resolved! CISCO 1841 Needs & Requirements

I have a CISCO 1841 router with a serial card connected to a diginet line and a ethernet connected to my switch all configured and working fine. My question is the following.I  have a Netgear ADSL device also connected to my switch which is used for ...

Load more