We have multiple Layer 2 MPLS networks deployed with Cisco ASR920 routers. We have issues matching/denying traffic on ACLs. We tried 3 options1. Applying the ACL inbound on the physical interface closest to the source - Doesn't match anything 2. Appl...
Bonjour S'il vous plait, je souhaiterais savoir si le Routeur Cisco 897VA est compatible avec port SFP base 1000 LX si oui, comment le configurer pour le WAN avec ces informations settings: Full duplexSpeed 1000Mb/sAutoneg OFF (si vous lai...
Hi experts, It was long time ago when I studied BGP, and these days I was doing a lab and got some issues related with the BGP router-id. I found this post:https://community.cisco.com/t5/routing/bgp-router-id-and-loopback/td-p/1611333Herve says "The ...
Dear community,We intend to purchase a C8200L supporting PIM interface with P-LTEA-EA module, The licenses we ordered are : C8000-HSEC, DNA-P-T1-E-3Y, SVS-PDNA-T1-E3Y, NWSTACK-T1-E, SDWAN-UMB-ESS and DNAC-ONPREM-PFDoes the above licenses enough for: ...
Hi all,Hopefully someone can help me out. I have a 5515x running and clients using AnyConnect to VPN in. Connected to this ASA is the link to Express Route and we're advertising (BGP) subnets from the ASA to Express Route, they all work however peopl...
Hi,Consider a situation where two main offices(core1 and 2) are located at different locations to provide redundancy. Using DMVPN and OSPF, I have a branch connected to multiple hubs, again in separate DC sites. The branch advertises its LAN to OSPF(...
How to determine which next hop interface should be used for configuring default static route on any router if it is connected to multiple routers at its various interfaces? Also, how to choose next hop for configuring static route for any destinatio...
Hello community,I have a question regarding default gateway. If L2 switch (the same applies to L3 switch & Router with disabled routing and any other host with IP which can't route) doesn't have default gateway configured, how it will reply to packet...
Hi I recently replaced a Juniper firewall with a Cisco ASA 5505 at a branch office. This branch office has a site to site VPN to another head office. Firewall at head office is a Juniper and managed by third party. I configured the ASA and replaced J...
Hello, I am learning the EIGRP basics in GNS3 and have added loopback interfaces and interfaces gi0/0 into the EIGRP AS. During establishing adjacency, I notice that the EIGRP update packet sent by R2 has a next-hop ip 0.0.0.0. Can someone explain w...
Before the Shutdows and No Shutdows errors occur on the Internet WAN pin of the device and make the Internet WAN available, but the error follows logging.Rouer ASR1001-X01 version equipmentCisco IOS XE Software, Version 03.16.05.S - Extended Support ...
Hi! I recently bought a Cisco 891F to use in my lab, but it can't get the full internet speed, (600/300 Mbps). Can it handle those speeds? If not, what is the point of having a GbE Wan? How can I use it? Currently, it is getting 95/95 Mbps.What route...
Hello My Assignment is: Use traceroute and debug (standby) commands to verify your network functionality. So I use the command debug ip icmp. After that traceroute 221.221.221.254(Destination IP). The port is unreachable. But if I use "ping 221.221....
Hi Partners! I have a problem configuring forty-two BVI interfaces on Cisco NCS 55A1. The problem began after configuration 30 of 42 BVI whit Anycast Routing (Host Routing) the other BVI interfaces automatically were rejected by the subsequent notifi...
We are seeing an issue where route filtration is not working, when we are redistributing static routes to OSPF area0. We have some static NULL routes in our SW01-WAN, which we don't want to redistribute towards SW01-CORE, but it getting redistributed...
