Hi,I got the below mentioned error message in my Cisco 7606 router.Can someone let me know the reason which caused this error message and what action to be taken to resolve it if there is some issue. This device was being remotely accessed and no one...
Hi,I have configured ether-channel b/w 6500 and 3750 stack, and now the interface in ether-channel doesnt work and caused 3750 stack to go down.I checked the interface on stack switch and found the ether-channel down, but where as the connecting port...
Hello,If I have a small private network with 2 ISPs homed on the same router but the service is Cable and DSL and neither IPS will advertise the others IP addresses is there any point in still running BGP on the router? Can anyone list a few benefi...
Hi, I would like to confirm if I have two 3845 CE routers peering with say two 7206 routers. 7206-1 7206-2 | \/ | ebgp /\ ebgp | / \ | 3845-1 --ibgp-- 3845-2 In the above setup, the 3845-1 would be the...
Hello there,I hope one of you techies can help me with this problem.I need to put in additional resilience into our network due to a problem we recently experienced.We currently have routes out our network via two pix's (in a failover config) which c...
Hi Pros,I've been reading many posts regarding distributing multicast from one location to another over the internet.I understand that multicast is difficult as well as limited (if at all possible) over IPSEC site-to-site VPN. It seems the best poss...
Hi,How many DS3 Card can support by 3845 rotuer
GreetingI want to let traffic which network admin doing ssh into the router go to different interface.that is all traffic to goto/comein my domain go interface vlan2; but if I want access the router, the ssh traffic will go interface vlan3.how can I ...
Hi, I have configured Virtual-Templete over PPP on Frame Relay connectivity. THe problem is, whenever I am configuring EIGRP or OSPF. Then Neighbor is established, but it is not advertising the Routes/Network......
Hi,I am facing problem with redistribution in ospf from RIP.Router under consideration (R1) is running RIP and OSPF. OSPF on serial 1 and RIP on serial 2. When OSPF neighbor is configured for RIP to ospf redistribution, naturally all routes are le...
Hello All, I created two V-templs on R1 pointing to R3 and R4 as shown here:R1interface Virtual-Template13interface Virtual-Template14R3interface Virtual-Template31R4interface Virtual-Template41And as a result of this, two virtual-Access was...
Hi,I have 1 MB lease line connected to the router. The interface is showing bandwidth utilization 100 Kb/s in inbound direction and 200 Kb/s in outbound direction. How can i calculate that how much i am using from 1 Mb. is i have to combine both of t...
I found that my C4507 switch has received huge of HOSTFLAPPING with the prefix 0C:CC:01 & 0C:CC:01 :C4507#show log1378604: Mar 27 18:30:01.959 : %C4K_EBM-4-HOSTFLAPPING: Host 0C:CC:01:00:0C:CC in vlan 10 is flapping between port Gi5/1 and port Gi5/21...
Hi,We have a 6509 with a lot of T1 or T3 circuits on it from different spoke sites. We also have an IDS connected on that 6509. How do you do port mirroring on that 6509 so IDS can catch traffic between the spoke sites? SPAN will not work because ...
A 7200 with huge configuration :-(, its taking lot of time to see the running config and the cpu shoots up every time.So planing to parser config cache interfacebut some clarifications required1. in whihc memory config will be stored ?2.what are the...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM |
| User | Count |
|---|---|
| 5 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |
